Ross Carbonite Black, Руководство по установке

Страница: 36 / 56

2. Use the Func knob to select the second function
of the Next button.
•
<none> — no secondary function
• GPO
— you can manually trigger a GPI
output
Next Transition Reset
You can have the transition area reset to a default
background dissolve after each transition. This allows
you to prevent the selections from the last transition
from being accidentally included with the next
transition.
To Set the Next Transition Reset Behavior
1.
Press
MENU Pers
>
NEXT
>
NEXT
>
Trans
Area .
2. Use the Trans knob to select whether the
transition area is reset after a transition.
•
NotRst — area is not changed after a
transition
• Reset
— area is reset to a background
dissolve after each transition
Next Transition Toggle
You can set the next transition selection buttons to
either be latching (toggle) or momentary (off). When
in toggle mode, pressing one of the next trans buttons
( BKGD , KEY1 , KEY2 , KEY3 , KEY 4 ) toggles it on
or off (unless it is the last button - at least one must be
selected). When off, pressing one button deselects all
other buttons. You must press all the buttons you want
to include in the next transition simultaneously.
To Set the Next Trans Toggle
1. Press MENU Pers > NEXT > Toggle .
2. Use the NTrans knob to select whether the
next transition buttons are latching (
Toggle
) or
momentary ( Off ).
• Toggle
— when you press a next transition
button it toggles on or off and does not change
the other buttons.
• Off — when you press a next transition button
it selects that button and turns off all other
buttons. You must press the buttons at the
same time to select them as part of the next
transition.
Power-Save Mode
The switcher goes into a Power-Save mode after a
user-defined amount of time (20 minutes by default)
without user interaction. Touching any button, knob, or
fader will wake the switcher. The switcher does not act
on the button, knob, or fader control that wakes it from
sleep mode.
During Power-Save mode, video related hardware is
not affected and video signals still pass through the
switcher.
To Set the Power Save Mode and Timer
1. Press MENU Pers > NEXT > NEXT .
2. Press the Sleep / PwrSve knob to toggle between
the power save modes.
•
Sleep — displays are turned off and buttons
light in raindrop pattern
• PwrSve — all buttons and displays are turned
off and as much power is conserved as possible
3. Use the Sleep / PwrSve knob to set the amount
of time that the switcher will wait without user
input before going into sleep or power-save mode.
Setting the value to off prevents the switcher from
ever going into sleep or power-save mode.
Roll GPO/Roll Clip
The switcher uses a GPI output to start a clip playing
on an external video server. This can be set to have the
GPI output always trigger if a source going on-air is
from a video server, or you have to set the GPI output
to trigger manually.
If your external video server supports the AMP
protocol, the roll clip functionality works directly
without the use of a GPI output.
To Set the Roll GPO/Clip Behavior
1.
Press
MENU Pers
>
NEXT
>
NEXT
>
Trans
Area > NEXT > NEXT .
2. Use the RlClip knob to select whether GPI
outputs, or video servers, assigned to input sources
are triggered before a transition.
•
Force
— the GPI output, or video server, is
always triggered with the transition
• User — you must select to trigger the GPI, or
video server, output with the transition
Shift Toggle
You can set the Shift button on the bus map to be
either latching (toggle) or momentary (off). When in
toggle mode, you can press the shift button and then
select a source on the shifted bus without having to
hold down the shift button. This only affects the bus
the shift button is on.
36 • Switcher Personality — Carbonite Black Setup Manual (v14.0)