Ross Carbonite Black, Руководство по установке

Страница: 35 / 56

3. Use the KeyCol knob to select whether the
buttons for each keyer are assigned a unique color
( On ), or if the keyer buttons all use the same color
( Off ). Depending on the color scheme selected,
key 1 is yellow, key 2 is green, key 3 is blue, and
key 4 is purple.
4. Press the Load knob.
5. Press the Confrm knob.
To Create a Custom Panel Color Scheme
Custom colors are created using standard hue,
saturation, and luminance values. Once created, you
can save your custom color.
1.
Press MENU > User > Scheme > NEXT .
2.
Use the Hue knob to adjust the hue of your
custom color.
3.
Use the Sat knob to adjust the saturation of your
custom color.
4.
Use the Lum knob to adjust the luminance of your
custom color.
5.
Press NEXT .
6.
Use the Save knob to select the custom scheme
that you want to store the custom color to.
7. Press the Save knob.
8. Press the Confrm knob.
To Set the Brightness of the Control Panel
Buttons
Note: Brightness is not stored with the color scheme.
1. Press MENU > User > Scheme > NEXT >
NEXT > NEXT .
2. Use the Brightness knob to set the brightness of
the buttons on the control panel.
Double-Press Rate
You can set the double-press rate of the switcher to
suit your preference. Setting a fast rate requires you
to double-press the knobs in quick succession in order
to be recognized as a double-press. Setting a slow rate
allows more time between presses but may register two
single presses as a double-press.
To Set the Double-Press Rate
1. Press MENU Pers > DblPrs Speed .
2. Double-press the HERE knob at the rate you want
to use for double-pressed on the switcher.
3. Press MENU to store the new rate.
Editor Mode
The switcher can be controlled by an external editor.
The external editor can control the switcher to perform
transitions, or recall memories, among the supported
commands.
Refer to the GVG100 Supported Protocol Document
for a list of supported commands.
To Set the Switcher to Editor Mode
Tip: You can quickly turn off editor mode by pressing and
holding the
MENU
button and pressing
PERS
.
1.
Press MENU Pers .
2.
Use the Editor knob to select On to allow the
switcher to be controlled by an external editor.
Memory Bank Button Behavior
Note: Note available on the CB1 and CB2.
The Memory Bank Button Behavior feature allows you
to set how the BANK button behaves when pressed
and released.
To Set the Bank Button Behavior
1.
Press MENU Pers > NEXT .
2.
Use the MemBnk knob to select how you want
the BANK button to behave when pressed and
released.
•
Normal — the keypad is used to enter the
bank number directly, followed by the memory
(For example, to access memory 3 on bank 2,
press BANK > 2 > 3 .)
• Legacy — the next bank is selected every
time the button is pressed, cycling through all
banks (For example, to access bank 5, press
BANK
repeatedly until bank 5 is selected.)
Next Button Secondary Function
You can configure the NEXT button to allow you to
manually trigger GPI outputs. This allows you to use
the GPI to manually roll a clip on a video server, or
load the next page on a character generator. Refer to
the External Device Setup Sheets for more information
on setting up an using external devices.
Refer to
GPI Control on page 39 for more
information on setting up and using GPIs.
To Set the NEXT Button Secondary Function
1. Press MENU Pers > NEXT > NEXT > NextBn
Func2 .
Carbonite Black Setup Manual (v14.0) — Switcher Personality • 35