Ross Carbonite Black, Руководство по установке, Страница: 26 / 56

Table 5: Available MultiViewer Sources
MultiViewer Inputs Outputs
2 1-3 3
3 4-6 4
4 7-9 5
Tip: To monitor a specific bus, such as ME program, assign
that source to one of the outputs that are available to the
MultiViewer. This also allows you to change what buses are
being monitored using an aux panel rather than changing the
MultiViewer setup.
To Set Up a MultiViewer
Note: A MultiViewer must be assigned to a video output to be
usable.
1. Press MENU > System > MultiView . Click
Navigation Menu > Configuration >
MultiViewers .
2.
Use the MView knob to select the MultiViewer
that you want set up. Click MultiViewer
X
to
select the MultiViewer you want to set up.
3. Use the Layout knob to select the arrangement
of the boxes that you want to use for the selected
MultiViewer. Click the Layout button and select
the arrangement of the boxes that you want to use
for the selected MultiViewer.
4. Use the Transp knob to adjust the transparency
of the background behind the source label for the
selected MultiViewer. Use the Transparency
slider to adjust the transparency of the background
behind the source label for the selected
MultiViewer.
5.
Press
NEXT
.
6.
Use the
Ovrlay
knob to turn the overlay on (
On
)
or off ( Off ). Click the Overlay button and click
On
to turn the overlay on, or
Off
to turn it off.
Tip: The overlay source can be used to overlay a
camera shot of a shot-clock over the MultiViewer output.
7. Use the Src/C knob to select a video source that
you want to overlay over the MultiViewer output.
8. Press the Src/C knob and use the S/Clip knob to
adjust the clipping of the overlay source. Use the
Clip slider to adjust the clipping of the overlay
source.
At
0%
the overlay source is completely opaque,
and at 100% it is completely transparent.
9. Press NEXT .
10. Use the Tally knob to select how boxes on the
MultiViewer are tallied. Click a Tally button to
select how boxes on the MultiViewer are tallied.
•
Box — red or green border is shown around
the outside of the MultiViewer box
• Label — red or green boxes are shown inside
the label area of the MultiViewer box
•
LblRevLabel Reverse — the same as Label,
but the placement of the tally boxes is swapped
11. Press NEXT .
12. Use the FSLBL knob to select whether FSFC
is shown on the source labels (
On
) or not (
Off
)
when a FSFC is applied to the source. Click an FS
Label
button to select whether FSFC is shown on
the source labels ( On ) or not ( Off ) when a FSFC
is applied to the source.
13. Press NEXT .
14. Use the Box knob to select the box on the
MultiViewer grid that you want to configure.
Click on one of the
Boxes
buttons and set up how
that box appears on the MultiViewer.
For example,
MV1:4 is box 4 on MultiViewer 1,
and MV2:3 is box 3 on MultiViewer 2.
• Input/Output — select the video source or
bus that you want to assign to this box on the
MultiViewer. When you assign an output to a
box, the switcher routes the source selected on
that bus to the box, and not the output of the
bus.
•
Green Tally — turn the preview (green) tally
for the MultiViewer box on or off.
•
Red Tally — turn the program (red) tally for
the MultiViewer box on or off.
• Border
— turn the border around the
MultiViewer box off ( Off ), white ( White ),
or black (
Black
). When the border is turned
off, some distortion may be visible around the
edges of the box.
• Label — turn source labels for the
MultiViewer box off, or on in a selected
position
• Label Pos — select a position for the source
label for the MultiViewer box( Bottom or
Top ).
•
Aspect — turn aspect ratio markers for the
MultiViewer box on (
Aspect
) or off (
Off
).
26 • Video Outputs — Carbonite Black Setup Manual (v14.0)