manualshive.com logo in svg

Ross 4500DR-204-03, Руководство пользователя

Поделиться
Скачать
Ross 4500DR-204-03 Скачать руководство пользователя страница 17

ACO-4500 User Guide (v3.0)

Physical Installation • 17

Physical Installation

If you have questions pertaining to the installation of ACO-4500, please contact us at the numbers listed in the 
section “

Contacting Technical Support

”. Our technical staff is always available for consultation, training, or 

service.

For More Information on...

• the technical specifications for the ACO-4500, refer to the chapter “

Technical Specifications

” on page 55.

Before You Begin

Before installing the ACO-4500, refer to the document “

Important Regulatory and Safety Notices to Service 

Personnel

” that accompanied your unit for general safety information.

Static Discharge

Throughout this chapter, please heed the following cautionary note: 

Operating Environment Requirements

Keep the following in mind before installing the ACO-4500:

• Verify that the location of your installation has the proper operating environment. The ACO-4500 operates 

correctly in ambient temperatures from 0°C to +40°C and relative humidity from 20% to 80%.

• The ACO-4500 requires 2”(50mm) of side clearance for counter top use. Also, ensure sufficient rear clearance, 

e.g. 3”(75mm), so that cables are not compromised.

• The ACO-4500 does not currently have an internal fan to assist with ventilation or cooling. Therefore, when you 

install the unit in an equipment bay, it is imperative that you ensure there is sufficient space all around the unit to 
allow the airflow to vent away any excess heat generated by the unit. 

For More Information on...

• environmental operating specifications, refer to the chapter “

Technical Specifications

” on page 55.

Unpacking

Unpack each ACO-4500 you received from the shipping container and ensure that all items are included. Initial 
Product Inspection

Perform the following when you receive your ACO-4500:

1. Inspect the shipping carton for external damage, which may indicate possible damage to the ACO-4500. If 

damage exists, document it, including photographs, to support any insurance claim.

2. Remove the instrument from the shipping carton.

3. Check that the ACO-4500 has not been damaged in transit. The exterior should not have any scratches or 

impact marks. Prior to shipment, the ACO-4500 is thoroughly inspected for mechanical defects.

4. Verify that the shipping carton contains the instrument, the standard accessories, and any optional accessories 

that you ordered. 

ESD Susceptibility

 — Static discharge can cause serious damage to sensitive 

semiconductor devices. Avoid handling circuit boards in high static environments such as 
carpeted areas and when synthetic fiber clothing is worn. Always exercise proper grounding 
precautions when working on circuit boards and related equipment.

Caution

 — The ACO-4500 could be damaged if it is powered on at temperatures or 

humidities outside the specified ranges.

Содержание 4500DR-204-03







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды