Rosemount Series 8700 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 122

background image

Reference Manual

00809-0100-4727, Rev EA

October 2010

Rosemount 8700 Series

2-8

NOTE

Do not bolt one side at a time. Tighten each side simultaneously. Example:
1. Snug left
2. Snug right
3. Tighten left
4. Tighten right
Do not snug and tighten the upstream side and then snug and tighten the
downstream side. Failure to alternate between the upstream and downstream
flanges when tightening bolts may result in liner damage.

Always check for leaks at the flanges after tightening the flange bolts. Failure
to use the correct flange bolt tightening methods can result in severe damage.
All sensors require a second torquing 24 hours after initial flange bolt
tightening.

For sensors with ANSI 600# full rated, 900#, 1500#, and 2500# flanges, the
liner is protected from over-compression by the flange design. Standard
flange torque specifications as determined by ANSI and ASME should be
followed. No special precaution is required to prevent liner damage caused by
over torquing. Bolt tightening procedures laid out in this Quick Installation
Guide must still be followed.

To prevent liner damage on any magnetic flowmeter, a flat gasket must be
used. For optimum results on meters with high pressure flanges (ANSI 600#
or above), it is recommended that a flat full face gasket be used.

Under NO circumstances should a spiral wound or flexitallic gasket be used
as this will damage the liner sealing surface.

Table 2-1. Flange Bolt Torque Specifications for Rosemount 8705 and 8707
High-Signal Sensors

PTFE/ETFE liner

Polyurethane liner

Size

Code

Line Size

Class 150

(pound-feet)

Class 300

(pound-feet)

Class 600

(1)

(Derated to

1000 psi)

(1) Derated available with PTFE lining only.

Class 150

(pound-feet)

Class 300

(pound-feet)

005

0.5-in. (15 mm)

8

8

8

8

-

010

1- in. (25 mm)

8

12

13

13

-

015

1.5-in. (40 mm)

13

25

29

29

7

020

2-in. (50 mm)

19

17

20

20

14

030

3-in. (80 mm)

34

35

41

41

23

040

4-in. (100 mm)

26

50

68

68

17

060

6-in. (150mm)

45

50

77

77

30

080

8-in. (200 mm)

60

82

121

121

42

100

10-in. (250 mm)

55

80

129

129

40

120

12-in. (300 mm)

65

125

146

146

55

140

14-in. (350 mm)

85

110

194

194

70

160

16-in. (400 mm)

85

160

274

274

65

180

18-in. (450 mm)

120

170

432

432

95

200

20-in. (500 mm)

110

175

444

444

90

240

24-in. (600 mm)

165

280

731

731

140

300

30-in. (750 mm)

195

375

-

-

165

360

36-in. (900 mm)

280

575

-

-

245

See ”Safety Messages” on pages 2-1 an d 2-2 for complete warning information.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
14
15
16
17
18
...
»

Содержание Series 8700



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Series 8700

Бренд: Valeport Страницы: 25

Бренд: Kane Страницы: 19

Бренд: ICS Страницы: 2

Бренд: CAISSON Страницы: 5

Vigilant ELM Series

Бренд: Eagle Eye Power Solutions Страницы: 9

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: Gazelle Страницы: 2

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: Jasco Страницы: 48

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: janitza Страницы: 48

Бренд: Tohnichi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды