Rosemount 3107 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 148

background image

72

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

Section 4: Configuration

4.3.32

Target frequency (P045)

This sets the frequency used for transmitting an ultrasonic pulse. The optimum frequency
depends on the characteristics of the transmitter’s piezoelectric crystals, which are affected by
temperature.

The transmitter has a look-up table to select a frequency value to give the highest echo strength
from the prevailing conditions at the site. This look-up function operates when Target
Frequency (P045) is set to “

Auto

”.

Site conditions sometimes require a fixed frequency. Target Frequency (P045) is used to set a
fixed frequency, but the actual frequency value used is selected from the look-up table and the
nearest to that entered value is selected automatically.

Note



See also

Frequency

) for the actual frequency used.

Field Communicator or AMS

To view or change the target frequency:

1.

From the

Home

screen, select

2: Configure

.

2.

Select

2: Manual Setup

.

3.

Select

7: Advanced Processing

.

4.

Select

6: Set Frequency

.

5.

Select

1: Target Frequency P045

.

6.

Select a new setting, and then select “

ENTER

” to save it.

7.

Press “

SEND

” to update the transmitter.

Rosemount 3490 Series Control Unit

To view or change the target frequency:

1.

From the

Main Menu

screen, select

SETUP

.

2.

Select the transmitter (e.g. “

Tx1: 3107

”).

3.

Select

ENGINEERING

.

4.

Select

ADVANCED

.

5.

Select

Target Freq

.

6.

Follow the on-screen instructions to edit and save the new setting.
(Press the

Enter

(

) key if prompted to change the mode to “off-line”).

7.

Select “

Quit

” to exit to the previous menu.

Fast Keys

2, 2, 7, 6, 1

Target Frequency P045
AUTOMATIC

50 kHz
51 kHz
53 kHz
54 kHz
56 kHz
58 kHz
AUTOMATIC

AUTOMATIC

ENTER

ESC

(Field Communicator Screen)

Target Freq P045

Auto kHz

Esc=Quit =Edit

(Rosemount 3491 Screen)

«
...
80
81
82
83
84
...
»

Содержание 3107





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3107

Бренд: Canon Страницы: 58

Бренд: CAME Страницы: 2

Бренд: Radionode Страницы: 20

CARBOCAP GMM112

Бренд: Vaisala Страницы: 2

Бренд: V2 Страницы: 76

Бренд: IBM Страницы: 411

Бренд: Standard Страницы: 71

Бренд: Kenwood Страницы: 2

Бренд: Kenwood Страницы: 29

Бренд: Kenwood Страницы: 16

Бренд: Kenwood Страницы: 20

Бренд: Kenwood Страницы: 23

Бренд: Kenwood Страницы: 38

Бренд: Kenwood Страницы: 38

Бренд: Kenwood Страницы: 60

Бренд: Kenwood Страницы: 46

Бренд: Kenwood Страницы: 48

Бренд: Kenwood Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды