Rosemount 3107 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 148

background image

51

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

Section 4: Configuration

4.3.14

Primary variable units (P012)

This selects alternative display units for the HART Primary Variable (PV), which are then reported
to a HART Master Device such as a Rosemount 3490 Series Control Unit.

Note



Selecting alternative display units does not automatically re-scale the PV value.
Use the parameter

PV Scale Factor

to manually re-scale the value.

Field Communicator or AMS

To view or change the displayed units for the PV:

1.

From the

Home

screen, select

2: Configure

.

2.

Select

2: Manual Setup

.

3.

Select

3: Profiling

.

4.

Select

1: Primary Variable Units P012

.

5.

Select new units, and then press “

ENTER

” to save

the selection.

6.

Press “

SEND

” to update the transmitter.

Note



If the HART PV has no units, select and confirm the “

None

”, “

Unknown

”, or

“

Not Used

”

option as appropriate for the HART Master Device (host).

Rosemount 3490 Series Control Unit

To view or change the displayed units for the PV:

1.

From the

Main Menu

screen, select

SETUP

.

2.

Select the transmitter (e.g. “

Tx1: 3107

”).

3.

Select

UNITS

.

4.

Select

PV Units

.

5.

Follow the on-screen instructions to select and confirm the new setting.
If the HART PV has no units, select and confirm the “

None

” option.

(Press the

Enter

(

) key if prompted to change the mode to “off-line”).

6.

Select “

Quit

” to exit to the previous menu.

Fast Keys

2, 2, 3, 1

Primary Variable Units P012
ft

Cum
Cum/h
Cum/s
ft
gal/min
Impgal
Impgal/d

ft

ENTER

ESC

(Field Communicator Screen)

PV Units P012

ft

Esc=Quit =Edit

(Rosemount 3491 Screen)

«
...
59
60
61
62
63
...
»

Содержание 3107





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3107

Бренд: XIEGU Страницы: 48

Бренд: XIEGU Страницы: 13

Бренд: B-band Страницы: 28

Бренд: Lamtec Страницы: 80

Бренд: Datcon Страницы: 40

Бренд: Q5X Страницы: 2

Бренд: Fairchild Страницы: 8

Бренд: MAMAC SYSTEMS Страницы: 4

Бренд: Icom Страницы: 40

Бренд: EBS Страницы: 58

FTDX 9000 Series

Бренд: Yaesu Страницы: 12

Бренд: Solartron Metrology Страницы: 25

Бренд: ADTRAN Страницы: 24

FTDX5000 - SOFTWARE UPDATE INFORMATION...

Бренд: Yaesu Страницы: 10

Бренд: Dolphin Страницы: 17

IC-F3260 Series

Бренд: Icom Страницы: 40

AXIS TX PICO PLUS

Бренд: Wave Central Страницы: 15

Бренд: PR electronics Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды