Rosemount 3107 Скачать руководство пользователя страница 39

Страница: 39 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

Section 4: Configuration

4.2.9

Simulate current output

This forces a fixed output current in the range 4 to 20 mA. This feature

temporarily

overrides the

normal function of the transmitter’s PV driving the 4–20mA Current Output until exiting to the
previous menu.

Note



The simulation is automatically cancelled after 20 minutes, and the output current
returns to representing the transmitter’s PV.

Field Communicator or AMS

To fix the output current:

From the

Home

screen, select

3: Service Tools

Select

5: Simulate

Select

2: Loop Current

Select

1: Loop Test

Select the required output current e.g.

1: 4mA

When a message appears saying the output current is fixed, press “

”.

Select

4: End

to exit and restore the output current to normal.

Note



When messages appear, take appropriate action if needed and press “

”.

Rosemount 3490 Series Control Unit

To fix the output current:

From the

Main Menu

screen, select

SETUP

Select the transmitter (e.g. “

Tx1: 3107

”).

Select

SYSTEM

, and then select

TRIM

Select

Fix Current

Follow on-screen instructions to input the required output current.
(Press the

Enter

(

) key if prompted to change the mode to “off-line”).

When finished, select “

Quit

” to exit to the previous menu.

Fast Keys

3, 5, 2, 1

Choose analog output level

1. 4mA
2. 20mA
3. Other
4. End

1. 4mA

ENTER

ABORT

(Field Communicator Screen)

Fix Current

0.000

Esc=Quit =Edit

(Rosemount 3491 Screen)

Содержание 3107





















































































































































Результаты поиска

Содержание 3107

Отзывы:

Похожие инструкции для 3107

Бренды по названию

Популярные бренды

Rosemount 3107, Справочное руководство

Результаты поиска

Содержание 3107

Отзывы:

Похожие инструкции для 3107

Бренды по названию

Популярные бренды