Rosemount 3107 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 148

background image

20

Reference Manual

00809-0200-4840, Rev BA

Section 4: Configuration

December 2014

Section 4: Configuration

and indicate when the connection is made. If the Field Communicator fails to connect, it
indicates that no device was found. If this occurs, check the lead connections and re-try.

A full menu map showing how to access transmitter parameters using the Field Communicator
is in Appendix

Appendix D: Field Communicator

4.2

Command parameters

4.2.1

Base units

When the transmitter is shipped from the factory, the default factory setting for

Base Units

is

“

metric

” or “

imperial ft

” depending on the model order code (see

“Ordering information” on

).

Note



Keep a record of your programmed settings. Changing base units resets parameters to
their default factory settings in the appropriate units.

Field Communicator

To view or change the transmitter base units:

1.

From the

Home

screen, select

3: Service Tools

.

2.

Select

4: Maintenance

.

3.

Select

3: Utilities

.

4.

Select

3: Set Base Units

.

5.

Use the up and down navigation keys to select new base units, and then save the
selection by pressing “

ENTER

”.

6.

Press “

ENTER

” to select

1: Yes

(in response to “Are you sure?”).

7.

Use the left navigation key to return to the previous menu.

Note



When messages appear, take appropriate action if needed and press “

OK

”.

Rosemount 3490 Series Control Unit

To view or change the transmitter base units:

1.

From the

Main Menu

screen, select

SETUP

.

2.

Select the transmitter (e.g. “

Tx1: 3107

”).

3.

Select

SYSTEM

.

Fast Keys

3, 4, 3, 3

Set Base Units (ft)

m
ft
in

ft

ENTER

ABORT

(Field Communicator Screen)

Base Units

Esc=Quit =Edit

metric

(Rosemount 3491 Screen)

«
...
28
29
30
31
32
...
»

Содержание 3107





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3107

MDS Mercury Series

Бренд: GE Страницы: 4

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 164

Бренд: Arteche Страницы: 9

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 2

Бренд: M-system Страницы: 2

Бренд: M-system Страницы: 2

Бренд: Mammut Страницы: 40

Бренд: Icom Страницы: 40

Tourguide Wireless Transmitter SR 2020 D

Бренд: Sennheiser Страницы: 32

IC-F3260 Series

Бренд: Icom Страницы: 40

Бренд: Danfoss Страницы: 2

STORM PRO C-4014

Бренд: Feniex Страницы: 13

Бренд: AirTest Страницы: 2

Бренд: Kanga Products Страницы: 26

Бренд: Gonset Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды