Rose electronics Orion XC OXS-XC008-FS Скачать руководство пользователя страница 17

Страница: 17 / 132

INSTALLATION

Orion XC Installation and Operation Manual

Installation

The installation section of this manual explains the basic System Setup. It then describes in detail how to set

up the Orion XC as a KVM Matrix, how to stack Orion XC matrices or make a grid of matrices.

System Setup

First time users are recommended to first connect all of the system components in the same room as a test

setup. This will facilitate correcting any cabling problems, and simplify the system configuration process.

Due to the construction of the matrix chassis, it is recommended to use an additional sub-floor below the matrix

for use in a 19” rack.

Setup of the matrix

Configure the Orion XC matrix as follows.

1. Connect a CON Unit to an I/O port of the matrix.

2. Connect a keyboard, mouse and monitor to the CON unit.

3. Connect the matrix and the CON unit to their power supplies and apply power.

4. Display the OSD menu with <'Hot Key'>, <o>, select

Configuration,

and login with administrator rights.

5. Configure according to application requirements.

6. Select

Save

in the Configuration menu, and then select

Restart Matrix

7. Optional: Establish a network connection between the matrix and a computer running the Java tool in order

to perform extended configuration.

Setup of Extenders

Configure the connected CPU and CON devices as follows.

1. Connect a CON unit to the matrix using CATx or fiber interconnect cables.

2. Connect the CON unit to the console devices (monitor, keyboard and mouse).

3. Connect the 5VDC power supply units to the CON unit and apply power.

4. Check the basic function of the CON unit by displaying the OSD menu with <'Hot Key'>, <o>.

5. Connect the source (computer, CPU) to the CPU unit of the extender by using the provided connection

cables.

6. Connect the CPU unit to the matrix by using CATx or fiber interconnect cables.

7. Connect the 5VDC power supply units to the CPU units.

8. Start the system by applying power to the Matrix.

Possible Orion XC Setups

The Orion XC can be set up in a variety of ways to provide the optimum system environment.

A portion of the Orion XC can be configured for single display computers, with another portion for multi-display

computers. The KVM and USB 2.0 support can also be configured.

Configuration of Orion XC can be performed through the OSD menus, using a keyboard and monitor

connected to an extender CON unit. It can also be configured through a network connection with a computer

running the Java Tool, or through the serial interface.

A connection to common media controls is also possible.

The following sections show the typical installations of the Orion XC.

Содержание Orion XC OXS-XC008-FS





































































































































Результаты поиска

Содержание Orion XC OXS-XC008-FS

Отзывы:

Похожие инструкции для Orion XC OXS-XC008-FS

Бренды по названию

Популярные бренды

Rose electronics Orion XC OXS-XC008-FS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Orion XC OXS-XC008-FS

Отзывы:

Похожие инструкции для Orion XC OXS-XC008-FS

Бренды по названию

Популярные бренды