Ronde & Schwarz 1424.6721K02 Скачать руководство пользователя страница 87

Страница: 87 / 148

Remote control commands

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

Figure 8-11: Example

Global Flags

Groups the settings for the power sensor behavior regarding S-parameter corrections.

S-Parameter Correction ON by Default ← Global Flags

If this option is enabled, the S-parameter correction is activated automatically when the
sensor is started.

S-Parameter Correction State Locked ← Global Flags

If enabled, the state that is selected with "S-Parameter Correction ON by Default" is
locked and cannot be changed using:

●

[SENSe<Sensor>:]CORRection:SPDevice:STATe

●

R&S

NRP2 base unit

S-Parameter Device Locked ← Global Flags

If enabled, the S-parameter device that is selected as the default device in the table of
S-parameter devices is locked and cannot be changed using:

●

[SENSe<Sensor>:]CORRection:SPDevice:SELect

●

R&S

NRP2 base unit

The default S-parameter device is the S-parameter device that you have selected
when the power sensor is started.

Configuring basic measurement parameters

Содержание 1424.6721K02





















































































































































Результаты поиска

Содержание 1424.6721K02

Отзывы:

Бренды по названию

Популярные бренды

Ronde & Schwarz 1424.6721K02, Руководство пользователя

Результаты поиска

Содержание 1424.6721K02

Отзывы:

Бренды по названию

Популярные бренды