Rolls-Royce Helicon X3 Скачать руководство пользователя страница 127

Страница: 127 / 140

Tools

Page 3 of 4

Doc. No.: 13S000411
Revision: A

1 General

This chapter lists required and recommended tools for installation and maintenance

purposes.

Note:

Tools required for maintaining subsuppliers equipment are not listed in

this chapter. Please refer to chapter

14 Subsuppliers Manuals

for details.

For maintenance and/or replacement of the sensors and position reference systems, the

separate manual from each manufacturer must be used.

Note:

For maintenance on electronic equipment, the use of electrostatic

discharge protection such as a wrist-band connected to a grounding point

is mandatory. A grounded surface is also recommended for such tasks.

2 Tools

2.1

Recommended Tools

The following tools are recommended for the installation and maintenance of this

system:
• Standard network technician tools
• Standard electrician tools
• Optic fibre termination tools (if applicable).

Caution: Always use appropriate tools for all maintenance tasks. Use of

inappropriate tools can lead to system malfunction.

2.2

Special Tools

No special tools are required for the installation and maintenance of this system.

Содержание Helicon X3


















































































































Результаты поиска

Содержание Helicon X3

Отзывы:

Похожие инструкции для Helicon X3

Бренды по названию

Популярные бренды

Rolls-Royce Helicon X3, Руководство пользователя

Результаты поиска

Содержание Helicon X3

Отзывы:

Похожие инструкции для Helicon X3

Бренды по названию

Популярные бренды