Roller Multi-Control S, Инструкция по эксплуатации

Страница: 28 / 136

defi ned with regard to the test methods A, B, C for pressure testing with water defi ned with regard to t defi ned with regard to t
offered in section 6.1 of EN 806-4:2010: "For reasons of practicability on the
building site, a modifi ed method based on practical tests which can be used for
all materials and combinations of materials was chosen. The test time has been
extended in relation to the time specifi ed in the standard to allow even the slightest
leaks to be detected. Test method B in accordance with DIN EN 806-4 is the basis
for conducting the leak test with water for all materials." The following is defi ned:
Leak testing with water can be conducted when
● changing of the water can be ensured at regular intervals, after seven days
at the latest, from the time of the leak test to commissioning of the drinking
water installation. Additionally when
● it is ensured that the house or building water connection is fl ushed and
therefore released for connection and operation,
● the pipe system is fi lled using totally hygienic components,
● the system remains full from the leak test to commissioning and partial
fi lling can be avoided.
WARNING WARNING
The hydro-pneumatic water pump installed additionally in the ROLLER’S
Multi-Control SLW for these tests is fed by the built-in compressor of the
ROLLER’S Multi-Control. The hydro-pneumatic pump generates a water pres- The hydro-pneumatic The hydro-pneumatic
sure of max. 1.8 MPa/18 bar/261 psi. Before conducting one of the tests with
water A, B, C, it must be assessed whether the installation to be tested will
withstand the preset/selected test pressure "p refer".
CAUTION CAUTION
Before disconnecting the high-pressure hose (26) from the pressure test with
water drain (25) or from the drinking water installation, make sure that the
pressure has been totally relieved.
The programs can be aborted at any time with the Esc button (10). Then all
the valves open and the pressure in the installation is released. The tests are
saved but "Cancel" is shown in the fi le.
The pressure test must be repeated if necessary or the installation must be
checked and improved.
NOTICE NOTICE
The controller ends the control process to set the selected test pressure in tests
with water at a tolerance of 0 to +0.3 bar. This means that the control is ended,
for example, when setting p refer = 11 bar at a value p actual between 11.0
and 11.3 bar. This tolerance is safe because, in the pressure test with water,
the relative pressure change of pressure p refer is decisive. If ENTER is pressed,
the value p actual is taken over as p refer. So the test can also be begun at a
p refer of 11.3 bar for example.
3.4.1. Pressure test with water, test method A (EN 806-4:2010, 6.1.3.2)
ter, test method A (EN 806-4:2010, 6.1.3.2)
Program sequence ↑ ↓ (8):
1. Test \ Enter
2. Test with water \ Enter
3. Test with water A \ Enter
4. Check reference test pressure default (p refer) and change if necessary (11) \ ↓
5. Check stabilisation default (t stabi) and change if necessary (11) \ ↓
6. Check test time default (t test) and change if necessary (11) \ ↓
7. Actual test pressure (p actual) is adjusted to reference test pressure (p
refer) \ Enter
8. Stabilisation/wait time (t stabi) running, actual test pressure (p actual) is
changed to reference test pressure (p refer) on expiring. The stabilisation/
wait time can be ended prematurely with Enter, the test time (t test) begins
immediately (\ Esc = cancel).
9. Display screen: Reference test pressure (p refer), actual test pressure
(p actual), differential test pressure (p diff), test time (t test) \ Enter
10. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.2. Pressure test with water,
3.4.2. Pressure test with water, test method Δ>10K (B/1): test method Δ>10K (B/1): Temperature Temperature
compensation (EN 806-4:2010, 6.1.3.3) compensation (EN 806-4:2010, 6.1.3.3)
Program sequence ↑ ↓ (8): Progr Progr
1. Test \ Enter
2. Test with water \ Enter
3. Test with water B \ Enter
4. Test Δ>10K (B/1) \ Enter
5. Check reference test pressure default (p refer) and change if necessary (11) \ ↓
6. Check stabilisation default (t stabi) and change if necessary (11) \ ↓
7. Check test time default (t test) and change if necessary (11) \ ↓
8. Actual test pressure (p actual) is adjusted to reference test pressure (p
refer) \ Enter
9. Stabilisation/wait time (t stabi) running, actual test pressure (p actual) is
changed to reference test pressure (p refer) on expiring. The stabilisation/
wait time can be ended prematurely with Enter, test time (t test) \ Enter (\
Esc = cancel).
10. Display screen: Reference test pressure (p refer), actual test pressure (p
actual), differential test pressure (p diff), test time (t test) \ Enter
11. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.3. Pressure test with water,
sure test with water, test method PfS (B/2): test method PfS (B/2): Press connections
unpressed leaking (information leafl et "Leak tests of drinking water installations unpressed leaking (information leafl et "Leak tests of drinking water installations
with compressed air, inert gas or water" (January 2011) of the German Central with compressed air, inert gas or water" (January 2011) of the German Central
Association for Sanitary, Heating and Air Conditioning (ZVSHK), supplement Association for Sanitary, Heating and Air Conditioning (ZVSHK), supplement
to EN 806-4:2010, 6.1.3.2.) to EN 806-4:2010, 6.1.3.2.)
Program sequence ↑ ↓ (8):
1. Test \ Enter
2. Test with water \ Enter
3. Test with water B \ Enter
4. Test PfS (B/2) \ Enter
5. Check reference test pressure default (p refer) and change if necessary (11) \ ↓
6. Check test time default (t test) and change if necessary (11) \ ↓
7. Actual test pressure (p actual) is adjusted to reference test pressure (p refer)
\ Enter, test time (t test) begins immediately (\ Esc = cancel)
8. Display screen: Reference test pressure (p refer), actual test pressure
(p actual), differential test pressure (p diff), test time (t test) \ Enter
9. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.4. Pressure test with water,
4. Pressure test with water, test method P+M (B/3): test method P+M (B/3): Plastic and metal pipe Plastic and metal pipe
systems (EN 806-4:2010, 6.1.3.3 and information leafl et "Leak tests of drinking systems (EN 806-4:2010, 6.1.3.3 and information leafl et "Leak tests of drinking
water installations with compressed air, inert gas or water" (January 2011) of water installations with compressed air, inert gas or water" (January 2011) of
the German Central Association for Sanitary, Heating and Air Conditioning the German Central Association for Sanitary, Heating and Air Conditioning
(ZVSHK). (ZVSHK).
Program sequence ↑ ↓ (8):
1. Test \ Enter
2. Test with water \ Enter
3. Test with water B \ Enter
4. Test P+M (B/3) \ Enter
5. Check reference test pressure default (p1 refer) and change if necessary
(11) \ ↓
6. Check reference test pressure default (p2 refer) and change if necessary
(11) \ ↓
7. Check test time default (t1 test) and change if necessary (11) \ ↓
8. Check test time default (t2 test) and change if necessary (11) \ ↓
9. Actual test pressure (p1 actual) is adjusted to reference test pressure (p1
refer) \ Enter, test time (t1 test) begins immediately (\ Esc = cancel)
10. Actual test pressure (p2 actual) is adjusted to reference test pressure (p2
refer) \ Enter, test time (t2 test) begins immediately (\ Esc = cancel)
11. Display screen: Reference test pressure (p1 refer), actual test pressure
(p1 actual), differential test pressure (p1 diff), test time (t1 test)
Reference test pressure (p2 refer), actual test pressure (p2 actual), differ-
ential test pressure (p2 diff), test time (t2 test) \ Enter
12. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.4.5. Pressure test with water, test method C (EN 806-4:2010, 6.1.3.4)
3.4.5. Pressure test with water, test method C (EN 806-4:2010, 6.1.3.4)
Program sequence ↑ ↓ (8):
1. Test \ Enter
2. Test with water \ Enter
3. Test with water C \ Enter
4. Check reference test pressure default (p refer) and change if necessary
(11) \ ↓
5. Check stabilisation default (t0 stabi) and change if necessary (11) \ ↓
6. Check test time default (t1 test) and change if necessary (11) \ ↓
7. Check test time default (t2 test) and change if necessary (11) \ Enter
8. Actual test pressure (p0 actual) is adjusted to reference test pressure (p 8. Actual test pressure (p0 actual) is ad 8. Actual test pressure (p0 actual) is ad
refer) \ Enter
9. Stabilisation/wait time (t stabi) running, actual test pressure (p actual) is
changed to reference test pressure (p refer) on expiring. The stabilisation/
wait time can be ended prematurely with Enter, the test time (t1 test) begins
immediately followed by test time (t2 test) (\ Esc = cancel).
10. Display screen: Reference test pressure (p refer), actual test pressure (p0
actual), differential test pressure (p0 diff), test time (t0 test)
Actual test pressure (p1 actual), differential test pressure (p1 diff), test time
(t1 test) actual test pressure (p2 actual), differential test pressure (p2 diff),
test time (t2 test) \ Enter
11. Esc >> Start menu \ Memory Manager, data transfer >> 3.8
3.5 Programs Testing gas pipe systems with compressed air (ROLLER’S
Multi-Control SL/SLW)
WARNING WARNING
This rule of the legal German accident insurance must be observed for Germany.
"Operation of work equipment", BGR 500, April 2008, chap. 2.31, Work
on gas pipes, industrial liability insurance association rule.
In addition, for Germany, the technical rule for gas installations "Technical
Rule Worksheet G 600 April 2018 DVGW-TRGI 2018 2018 2018" of the DVGW German
Gas and Water Association defi nes the following among other things:
"5.6.2 Safety measures during the tests": Safety measures may need to be
taken during the tests when carrying out the load test due to the compressibility
of gases. "The max. test pressure may not exceed the value of 3 bar. Every
sudden rise in pressure in the pipe system to be tested must be avoided."
The respective national safety provisions, rules and regulations valid for
the application site must be considered and observed.
Before conducting a test with compressed air, it must be assessed whether the
installation to be tested will withstand the preset / selected test pressure "p refer".
The tests described below and the defaults stored in the ROLLER’S Multi-Control
SL/SLW correspond to the "Technical Rule Worksheet G 600 April 2018 DVGW- 2018 2018
TRGI 2018" of the DVGW German Gas and Water Association valid in Germany.
eng eng
28