background image

 14 

Easy Spring Plus  

Roller Roman Fabrication

Troubleshooting

Shade is stuck at the bottom and will not raise. 

Did you remember to pre-rotate the spring?  Check to make sure spring has tension. (see step 9)

Check to make sure stop plate is not against stop spring.  (see step 7)

Shade must have enough slack to work properly.  The tube must be able to turn in the reverse direction for the
lock to disengage.  If the shade has run out of slack, rotate the tube about 1/4 turn (in the direction that the
string comes off the tube) by hand to disengage the lock.

   

See video 

titled “How to fix a stuck cordless Roman shade” 

Shade goes up too fast or slow. (Spring needs adjustment) 

Remove (or add) tension from the spring with the spring adjuster wheel.  Assuming the RollEase instructions 
were followed, the spring side will have a marker on the tube and the stop side will not. 

   When the 

spring is on your left facing the window

 

   

Too slow 

- add tension by rotating the wheel counter-clockwise (toward the bottom of the window). 

   

Too fast - 

remove tension by rotating the wheel clockwise (toward the top of the window).  

   When the 

spring is on your right facing the window

 

   

Too slow -

 add tension by rotating the wheel clockwise (toward the top of the window).   

   

Too fast - 

remove tension by rotating the wheel counter-clockwise (toward the bottom of the window).  

   

See video 

titled “

How to Adjust Spring Tension on the Easy Spring Plus Cordless Roman shade

” 

Shade stops too high or too low from top. (Stop needs adjustment) 

* Adjust stop height by turning the stop adjuster wheel.  Then, lower and raise shade to check.

   When the 

stop is on your right facing the window

  

   

Too high 

- lower by rotating the wheel clockwise (toward the bottom of the window)  

   

Too low 

- raise by rotating the wheel counter-clockwise (toward the top of the window). 

   When the 

stop is on your left facing the window

 

   

Too high 

- lower by rotating the wheel counter-clockwise (toward the top of the window)  

   

Too low 

- raise by rotating the wheel counter-clockwise (toward the bottom of the window). 

   

See video 

titled “

How to Adjust the Stop Position on the Easy Spring Plus Cordless Roman shade

” 

See all instructional videos at: 

http://www.rollease.com/support/trade/instructional-videos?view=fullpage or on the 

RollEase YouTube page.

Easy

Spring

Plus

CORDLESS SHADE SYSTEM

by Rollease Acmeda

Содержание Easy Spring Plus















Отзывы: