manualshive.com logo in svg

Rolando Texart XT-640, Руководство пользователя

Поделиться
Скачать
Rolando Texart XT-640 Скачать руководство пользователя страница 93

91

3

Maintenance

When Not in Use for a Prolonged Period

Keep Performing Maintenance

Switch on the power once a month

Switch on the sub power once a month. When you turn on the power, the machine automatically performs some 
operations such as those to keep the print heads from drying out. Leaving the machine unused for a prolonged 
period may damage the print heads, so be sure to switch on the power to perform these automatic operations.

Keep at a constant temperature and relative humidity

Even when the machine is not in use, keep it at a temperature of 15 to 30°C (59 to 86°F) and a relative humidity 
of 20 to 80% (with no condensation). Temperatures that are too high may degrade the ink and cause malfunc-
tions. Temperatures that are too low may cause the ink to freeze and damage the print heads.

Alarm Feature

The alarm feature reminds you to switch on the sub power once a month. When the machine remains unused 
for about one month, this screen appears and a warning beep sounds. If this screen appears, switch on the 
sub power. When maintenance operations finish, switch off the sub power.
This feature operates when the machine's main power is turned on. Leave the main power switched on at all 
times even when the machine is to remain out of use for a prolonged period.

If the Machine has not been Used for Over One Month

If the machine has not been used for over one month, refresh the subtanks. If you use the machine straight away 
without performing this procedure, printing may be adversely affected, e.g. printed colors may be unstable.

P. 78 "Refreshing Subtanks (REFRESH SUBTANKS)"

PRESS THE POWER
KEY TO CLEAN

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды