manualshive.com logo in svg

Rolando Texart XT-640, Руководство пользователя

Поделиться
Скачать
Rolando Texart XT-640 Скачать руководство пользователя страница 70

When Normal Cleaning Is Not Effective

3

Maintenance

68

Press 

.

The screen shown in the figure appears, and then cleaning starts.
The (approximate) remaining time for the procedure is displayed on 
the screen. ("01:45" = "1 minute and 45 seconds")

When cleaning finishes, the screen shown in the figure appears again.

Press 

, then 

 to go back to the original screen.

If problems such as dot drop-out persist even after you have performed medium cleaning, perform the more 
powerful "powerful cleaning."

Powerful Cleaning

Procedure

Press 

.

Press 

 to display the screen shown on the left.

Press 

.

The screen shown in the figure appears, and then cleaning starts.
The (approximate) remaining time for the procedure is displayed on 
the screen. ("01:45" = "1 minute and 45 seconds")

When cleaning finishes, the screen shown in the figure appears again.

Press 

, then 

 to go back to the original screen.

When powerful cleaning is not effective

If problems such as dot drop-out persist even after you have performed powerful cleaning several times, 
perform manual cleaning. Such cleaning can be effective when carried out periodically, according to the 
frequency of use.

 

P. 72 "Manual Cleaning"

CLEANING...
>>>>>      01:45

MEDIUM CL.
  AB

CLEANING
POWERFUL CL.

CLEANING...
>>>>>      01:45

CLEANING
POWERFULL CL.

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды