Rolando Texart XT-640 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 156

background image

Output Operation Management

5

To

Admin

-

istrators

119

Description

When “STOP” is selected, printing pauses, so colors may be uneven. Ensure that the remaining ink is sufficient
before you begin printing. When "CONT" is selected, printing does not stop even if ink runs out completely.
To replace an ink pouch, wait until printing ends or press

to pause printing.

Default Setting

[EMPTY MODE]: STOP

Displaying the Amount of Media Remaining

You can display how much of the media in use is left. By setting the amount of media currently remaining
at the start, the amount remaining will be constantly displayed on the display screen until it reaches zero.

Procedure



Press

.



Press

to display the screen shown on the left.

Press

, then

.



Press

.



Press

or

to set the current amount of

media remaining.

Press

to confirm your entry.



Press

, then

to go back to the original

screen.

Description

If you cancel media loading, for example by removing the media or raising the loading lever, the amount
remaining at that time flashes on the screen. Because the amount of media remaining is not updated auto-
matically when you change the media, redo the setting whenever you change the media. You can also set the
machine to display this menu automatically whenever you change the media. See the next section, "Making
Sure to Verify the Setting for the Amount Remaining Every Time the Media Is Changed."

* The remaining amount that is displayed is only an estimate. Accuracy is not assured.

MENU

SHEET REMAIN

SHEET REMAIN
SET LENGTH

SET LENGTH
0.0m 25.0m

W1200mm

Ｌ 25.0m

　　

SETUP SHEET
ROLL Ｌ　25.0m

This display is updated.

If media has not been loaded,

the set value flashes.

«
...
119
120
121
122
123
...
»

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Texart XT-640

Бренд: LabelTac Страницы: 2

Бренд: Canon Страницы: 300

Бренд: Canon Страницы: 288

Бренд: MAKER MADE Страницы: 21

Бренд: Canon Страницы: 58

Бренд: Canon Страницы: 30

870 - SuperScript B/W Laser Printer

Бренд: NEC Страницы: 8

Бренд: B3 innovations Страницы: 12

Бренд: F+D Feinwerk- und Drucktechnik Страницы: 22

Бренд: Xante Страницы: 6

Бренд: Xerox Страницы: 44

Бренд: Oki Страницы: 76

Бренд: Canon Страницы: 34

Бренд: Canon Страницы: 369

Бренд: Konica Minolta Страницы: 15

Бренд: Oki Страницы: 156

Бренд: Telpar Страницы: 52

Бренд: Konica Minolta Страницы: 404

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды