Rolando Texart XT-640 Скачать руководство пользователя страница 103

Страница: 103 / 156

Using the Dryer

Advanced

Functions

101

Setting the Drying Time after Printing

Procedure



Hold down

and press



Press



Press

to display the screen shown on the left.

Press



Press

to select the drying time.

Press

to confirm your entry.



Press

, then

to go back to the original screen.

Description

Set the drying time after the 1st page is printed. The next operation is not started until the set time passes.
During drying,

is lit. Press

while

is lit to finish the drying time and start the

next operation. Also, hold down

while

is lit to cancel the output.

You can also make this setting in the software RIP. When you have made the setting in the software RIP, the
software RIP's setting is used.

Default Setting

[DRYING TIME]: 0min

HEATER MENU
DRYING TIME

DRYING TIME
0min 10min

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Rolando Texart XT-640, Руководство пользователя, Страница: 103 / 156

Результаты поиска

Содержание Texart XT-640

Отзывы: