7
Menu List
System Menu
Menu item
Value
Explanation
Frame Rate
59 94
, 50 Hz
Specifies the frame rate.
HDCP Mode
Disabled
, Enabled
If this is set to “Enabled,” copy-protected (HDCP) video can be input. Also, HDCP is applied to
the video that is output.
Screen Mode
Matrix
, Split, Switcher
Specifies the screen mode of the video output.
Matrix:
Use the cross-point buttons to switch the combination of four inputs and four
outputs, and output the video. The internal frame synchronizer allows seamless
video switching.
Split:
Up to four screens of the video selected by the crosspoint buttons can be layer-
composited and output. The video of XPT 1 can also be key-composited.
Switcher:
The video of the PGM side (XPT3 row) is always output. The PST side (XPT4 row)
selects the preset video (the video that will be output next).
Use the [AUTO] button or operate the video fader to switch the video.
XPT Assign
(Enter)
Displays the cross-point assign detailed settings menu (see below).
* When in switcher mode, cross-point assign is only shown.
Test Pattern
(Enter)
Displays the test pattern detailed settings menu (p. 8).
EDID Copy
(Enter)
Displays the EDID copy detailed settings menu (p. 8).
Auto Memory
Disabled,
Enabled
If this is set to “Enable,” memory 1 functions as the last memory. When you close a menu or
recall a memory, the current settings are automatically saved in memory 1.
Auto Power Off
Disabled,
Enabled
Enables/disables the auto-off function.
If this is set to “Enable,” the power automatically turns off when 240 minutes elapse with the
XS-1HD in the following state.
5
The XS-1HD is not operated
5
Audio or video are not input
5
No output device is connected
Remote Baudrate
9600
, 38400 bps
Specifies the communication speed (bps) of the REMOTE connector (RS-232).
LED Dimmer
1–
8
Adjusts the brightness of the top panel LEDs.
Fader Calibration
(Enter)
Calibrates the video fader.
Factory Reset
(Enter)
Resets the unit to its factory-set state.
Version
—
Displays the system program version.
XPT Assign detailed settings menu
In Matrix Mode
Menu item
Value
Explanation
[Output]
[Input]
Specifies the cross-point that is assigned to each output. If this is set “Off,” video is not output.
5
When using four outputs, video transitions are separated by the background color.
5
By restricting the outputs, you can perform seamless video transitions that use dissolve.
Restrict to three outputs:
Seamless video transition is possible for one screen.
Restrict to two outputs:
Seamless video transition is possible for two screens simultaneously.
5
By combining cross-points and outputs, 2–4 screens can be spanned.
HDMI 1
Off, XPT 1–4
Default settings are as follows.
HDMI 1: XPT 1
HDMI 2: XPT 2
HDMI 3: XPT 3
HDMI 4: XPT 4
HDMI 2
HDMI 3
HDMI 4
In Split Mode
Menu item
Value
Explanation
[Output]
[Input]
Enables/disables (Off) the cross-point.
5
When compositing four screens, video transitions are separated by the background color.
5
By decreasing the number of screens to three or fewer, you can perform seamless video
transitions using dissolve.
* In split mode, the same image is always output from VIDEO OUTPUT 1–4.
HDMI 1
Off
, XPT 1
HDMI 2
Off
, XPT 2
HDMI 3
Off,
XPT 3
HDMI 4
Off,
XPT 4
