background image

 

10

 

Playing Methods

 

The hi-hat tone changes smoothly and continuously from 
open to closed in response to how far the pedal is pressed.
You can also play the foot closed sound (playing the hi-hat 
with the pedal completely pressed down) and foot splash 
sound (playing the hi-hat with the pedal fully pressed and 
then instantly opening it).

When you strike the hi-hat while pressing on the pedal with 
the hi-hat closed, you can then change the closed tone in 
response to the pressure you place on the pedal.

This playing method involves striking the middle area of the 
top hi-hat. It corresponds to the sound of the “head-side” of 
the connected trigger input.

 

fig.Play-01

 

This playing method involves striking the edge of the top hi-
hat with the shoulder of the stick. When played as shown in 
the figure, the “rim-side” sound of the connected trigger input 
is triggered.

 

fig.Play-02

 

Do not strike the bottom hi-hat or the underside of the 
top hi-hat.

 

Open/Closed

 

Pressure

 

Bow Shot

 

Edge Shot

Edge Sensor

 

Specifications

 

Size:

12 inches

Trigger:

2 (Bow/Edge)

Connectors:

TRIGGER OUTPUT Jack
CONTROL OUTPUT Jack

Dimensions:

314 (W) x 314 (D) x 89 (H) mm

12-3/8 (W) x 12-3/8 (D) x 3-9/16 (H) inches

Weight:

1.9 kg / 4 lbs 4 oz

Options

Owner’s Manual, Clutch, Clamp, 
Holder (3 types), Link Cable, 
Tuning Key, Cable Tie

 

962a

 

* In the interest of product improvement, the specifications and/

or appearance of this unit are subject to change without prior 
notice.

 

Compatible Stand

Diameter: 6.0–7.0 mm

(0.236"–0.276")

Diameter: 11.7 mm (1/2") Max.

Diameter: 25.4 mm (1")   

22.2 mm (7/8")
19.1 mm (3/4")

VH-12_e 10 ページ 2005年10月5日 水曜日 午前10時26分

Содержание VH-12













Отзывы: