Roland VariOS Скачать руководство пользователя страница 40

Страница: 40 / 168

Installation

■

Connections and OMS setup

Installing the VariOS OMS driver

Use the following procedure to install the VariOS driver.
The included

VariOS OMS Driver-E

is an add-on module for using the

VariOS with OMS. In order for you to use it,

OMS must already be

installed on the hard disk from which you started up

* Disconnect the VariOS from the Macintosh before you perform the installation.

Exit all currently running software (applications).

Insert the CD-ROM into the CD-ROM drive.

Double-click the

VariOS OMS Driver-E Installer

icon (found in the

English - for OS 9 - Driver - VariOS OMS Driver-E

folder of the CD-

ROM) to start up the installer.

Verify the

[Install Location]

, and click

[Install]

fig.3-2

If a message like the following is
displayed, click

[Continue]

The other currently running
applications will exit, and installation
will continue.

A dialog box will indicate Installation completed.

Click

[Restart]

to restart your Macintosh.

If you are using a virus
checker or similar software,
be sure to exit this as well.

Содержание VariOS









































































































































































Результаты поиска

Содержание VariOS

Отзывы:

Roland VariOS, Руководство пользователя, Страница: 40 / 168

Результаты поиска

Содержание VariOS

Отзывы: