Roland TM-6 PRO, Список данных

Страница: 27 / 37

27
TRIGGER SETUP
Parameter Value Explanation
Delay 1 Pan,
Delay 2 Pan
L64–63R
Stereo location of the tap delay
sounds
Delay 1 Level,
Delay 2 Level
0–127 Volume of the tap delay sounds
Low Gain -15–+15dB Gain of the low frequency range
High Gain -15–+15dB Gain of the high frequency range
Balance
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output level
PAN DELAY
Produces a delay sound that alternates between left and right.
Parameter Value Explanation
Tempo Sync OFF, ON
Specifies whether the delay time of
the left/right delay sound is specified
as a note value (ON) or not (OFF).
Delay Time(#) 1–2600ms, note
Adjusts the delay time from the
direct sound until the delay sound
is heard.
Delay Feedback -98–+98%
Adjusts the amount of the delay
sound that’s fed back into the effect.
Negative “-” settings will invert the
phase.
Delay HF Damp
200–8000Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect is
filtered out. If you don’t want to filter
out any high frequencies, set this
parameter to BYPASS.
Delay 1 Pan,
Delay 2 Pan
L64–63R Stereo location of the delay sounds
Delay 1 Level,
Delay 2 Level
0–127 Volume of the delay sounds
Low Gain -15–+15dB Gain of the low range
High Gain -15–+15dB Gain of the high range
Balance
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level
0–127 Output level
3TAP DELAY
Produces three delay sounds; center, left and right.
Parameter Value Explanation
Tempo Sync Left,
Right, Center
OFF, ON
Specifies whether the delay time
value of the left/right/center delay
sound is specified as a note value
(ON) or not (OFF).
Dly L, R, Ctr
Time(#)
1–2600ms, note
Adjusts the time until the delay
sound is heard.
Center Feedback
-98–+98%
Adjusts the amount of the delay
sound that’s fed back into the effect.
Negative “-” settings invert the phase.
HF Damp
200–8000Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect is
filtered out. If you do not want to
filter out any high frequencies, set
this parameter to BYPASS.
Left, Right,
Center Level
0–127 Volume of each delay
Low Gain -15–+15dB Gain of the low frequency range
High Gain
-15–+15dB Gain of the high frequency range
Balance
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output level
CHORUS
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Type of filter
OFF:
no filter is used
LPF:
cuts the frequency range above
the Cutoff Freq
HPF:
cuts the frequency range below
the Cutoff Freq
Cutoff Freq 200–8000Hz Basic frequency of the filter
Pre Delay 0.0–100.0ms
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Tempo Sync OFF, ON
Specifies whether the modulation
rate is specified as a note value (ON)
or not (OFF).
Rate(#)
0.05–10.00Hz,
note
Frequency of modulation
Depth(#) 0–127 Depth of modulation
Phase
0–180deg Spatial spread of the sound
Low Gain -15–+15dB Gain of the low range
High Gain -15–+15dB Gain of the high range
Balance(#)
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Level
0–127 Output level
SDD-320
This models Roland’s DIMENSION D (SDD-320). It provides a clear
chorus sound.
Parameter Value Explanation
Mode(#)
1, 2, 3, 4, 1+4, 2+4,
3+4
Switches the mode.
Low Gain -15–+15dB Gain of the low range
High Gain -15–+15dB Gain of the high range
Level 0–127 Output level
FLANGER
This is a stereo flanger (The LFO has the same phase for left and
right.). It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Type of filter
OFF: no filter is used
LPF:
cuts the frequency range above
the Cutoff Freq
HPF: cuts the frequency range below
the Cutoff Freq
Cutoff Freq 200–8000Hz Basic frequency of the filter
Pre Delay
0.0–100.0ms
Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
Tempo Sync OFF, ON
Specifies whether the modulation
rate is specified as a note value (ON)
or not (OFF).
Rate(#)
0.05–10.00Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180deg Spatial spread of the sound
Feedback -98–+98%
Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative “-” settings will invert the
phase.
Low Gain -15–+15dB Gain of the low range
High Gain -15–+15dB Gain of the high range