Travel Cover
Windscreen
With the work cover still in place, insert the
microphone section of the R-26 to the travel
cover.
Align the cloth portion on the inside of the
windscreen with the hook and loop fastener
on the work cover.
Attach the windscreen, while making sure
that the elastic is held by the notches in the
work cover (four places).
Fasten the snap fasteners on the rear (three
places).
Cover/Windscreen Set for R-26
OP-R26CW
Owner’s manual
Before using this product, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES”. These sections
provide important information concerning the proper operation of the product. Additionally, in order to feel assured that you have
gained a good grasp of every feature provided by your new product, Owner’s manual should be read in its entirety.
The manual should be saved and kept on hand as a convenient reference.
Work Cover/Strap
Insert the R-26 into the work cover, in the
direction shown in the illustration.
After the work cover has been put on the
R-26, pass the strap from above through the
slot on the R-26.
As shown in the illustration, attach the
strap securely, so it won’t come loose.
USING THE UNIT SAFELY
• Do not drop the R-26 or subject it to
strong impact while it is in this product.
Also, be careful not to drop the unit
when removing it from this product.
IMPORTANT NOTES
• Do not expose the product to direct
sunlight, place it near devices that
radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to
temperature extremes. Excessive heat
can deform or discolor the product.
Maintenance
• For everyday cleaning wipe the
product with a soft, dry cloth or one
that has been slightly dampened with
water. To remove stubborn dirt, use a
cloth impregnated with a mild, non-
abrasive detergent. Afterwards, be sure
to wipe the product thoroughly with a
soft, dry cloth.
• Never use benzine, thinners, alcohol
or solvents of any kind, to avoid the
possibility of discoloration and/or
deformation.
Main Material
Cover
Polyurethane cloth
(Front cloth)
Polyester (Inner cloth)
Windscreen
Acrylic
Strap
Polypropylene tape
* In the interest of product improve-
ment, the specifi cations and/or
appearance of this product are subject
to change without prior notice.
Copyright © 2011 Roland CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of Roland
CORPORATION.
Roland is a registered trademark of Roland Corporation in the United States and/or other countries.
• To ensure that the R-26 doesn’t get scratched when you insert it inside this product, carefully check to make sure that
no dirt, dust, or other foreign matter is stuck to the surface of the R-26 or on the inside of the cover.
• When using the work cover, always make sure that you also have the strap attached.
• Attach the strap securely so that it does not easily become detached. If the strap is loose, when carrying the R-26, it
could be dropped, possibly resulting in damage or injury.
• Use only the provided strap. The included strap is meant for exclusive use with the R-26. Do not use this strap for other
products.
• Check to make sure that the strap is securely fastened.
• In households with children, be careful with the parts that are used to adjust the strap, so as to prevent accidental
ingestion.
• Do not spin or swing the R-26 while holding it by the strap. This is extremely dangerous, as it may cause the strap to
become detached; or may even break the strap.
• Please note that some of the acrylic fur of the windscreen may fall out. Also note that it is not water repellent.
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US (Proposition 65)
Hook and loop
fastener
Notches
※ 日本語は裏面に掲載しています。
