Roland MV-8000 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

Roland MV-8000 Скачать руководство пользователя страница 7

7

Preparations and concepts

«

Preparations and concepts

Turning off the power

You must perform the Shutdown operation before turning the power off. The
Shutdown operation saves the stored parameters before powering-off, and
safely stops the hard disk.

1

Press .

A message of “SHUTDOWN Are you sure?” will appear.

2

Press (Yes).

A message of “Save Current Project before SHUTDOWN?” will appear.

3

Press (Yes).

The current project will save. When save process is completed, the
“SHUTDOWN Completed. You May Turn Off.” message will appear.

4

Turn down the volume of all connected equipment

5

Turn off the rear panel POWER switch.

Make sure that the “You May Turn Off.” message is displayed before you turn
off the power.

• When you turn off the power, you may hear a sound even though the MASTER

knob is turned down; this is not a malfunction.

• While the Shutdown process is occurring, system parameters and project/song

data is being saved. This will require a certain amount of time before the MV-8000
is ready for you to turn off the power.

If you press [EXIT] in step 3,
shutdown will be cancelled. If
you want to shutdown without
saving the current project,
press [F1 (No)].

If you turn off the power without performing Shutdown, or if you turn
off the power before “You May Turn Off.” is displayed, the data and
the MV-8000 itself will be damaged. Roland will accept no
responsibility for any damage that results from your failure to
perform the Shutdown operation.

QuickStart_e.book 7 ページ２００５年４月２８日　木曜日　午後９時３５分

«
...
5
6
7
8
9
...
»

Содержание MV-8000

































Отзывы:

Нет отзывов