Rohde & Schwarz SMCVB-K168 Скачать руководство пользователя

Страница: 24 / 91

DVB-S2 Configuration and Settings

R&S

SMCVB-K168

User Manual 1179.1064.02 ─ 03

Remote command:

[:SOURce<hw>]:BB:INPut:IP<ch>:ALIas

on page 67

Type

Sets the input signal type.

"Unicast"

Analyzes all unicast IP packets that arrive at the specified "Port".

"Multicast"

When an IP address is in the multicast address range, an attempt is
made to join a multicast group using

IGMP

Set "Multicast Address" and "Port".

Remote command:

[:SOURce<hw>]:BB:INPut:IP<ch>:TYPE

on page 67

Multicast Address

Editing requires "Type > Multicast".

Sets the destination IP address (IPv4) of the IP connection.

You can set addresses from "224.0.0.0" to "239.255.255.255".

Remote command:

[:SOURce<hw>]:BB:INPut:IP<ch>:MULticast:ADDRess

on page 68

Port

Sets the destination UDP port.

Due to

UDP

RTP

autosensing, we recommend that you set a port offset of at least 6

between neighboring IP TS channels.

Remote command:

[:SOURce<hw>]:BB:INPut:IP<ch>:PORT

on page 67

IGMPv3 Source Address

Requires "Type > Multicast".

Sets the

IGMPv3

source address.

If you need to filter the data sent to the multicast address, specify the source address.
A source address different from "0.0.0.0" accepts only data originating from the speci-
fied IP address.

Remote command:

[:SOURce<hw>]:BB:INPut:IP<ch>:IGMP[:SOURce]:ADDRess

on page 68

Ping Source Address

Clicking "Ping Source Address" triggers pinging of the IGMPv3 source address.

If you set a different value from "IGMPv3 Source Address = 0.0.0.0" and click the but-
ton, the software checks if the address is reachable.

Remote command:

[:SOURce<hw>]:BB:INPut:IP<ch>:IGMP[:SOURce]:PING

on page 68

Ping Result

Displays the result after pinging the source address.

If "Ping Result > Ping: Successful", the source address is available in the network.

Input Signal Settings

Содержание SMCVB-K168




























































































Результаты поиска

Содержание SMCVB-K168

Отзывы:

Похожие инструкции для SMCVB-K168

Бренды по названию

Популярные бренды

Rohde & Schwarz SMCVB-K168, Руководство пользователя

Результаты поиска

Содержание SMCVB-K168

Отзывы:

Похожие инструкции для SMCVB-K168

Бренды по названию

Популярные бренды