manualshive.com logo in svg

Rohde & Schwarz R&S RTM-B1, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz R&S RTM-B1 Скачать руководство пользователя страница 238

Network Connections and Remote Operation

R&S

®

RTM3000

238

User Manual 1335.9090.02 ─ 08

11.2

 

USB Connection

In addition to a LAN connection, you can use the USB connector at the rear panel to
access the instrument via USB.

Connecting the instrument using USB

1. Connect the USB cable to the USB type B connector at the rear panel of the instru-

ment, and to the computer.

2. Open the "Setup" menu.

3. Tap "Interface".

4. Tap "USB" to select USB connection.

5. Tap "Parameter".

6. Select the USB mode.

● USB TMC (Test & Measurement Class)
● USB VCP (Virtual Com Port)
● USB MTP (Media Transfer Protocol)

11.2.1

 

USB TMC

USB TMC means USB Test & Measurement Class. You can use this interface for
remote control of the instrument using SCPI commands. USB TMC does not need a
driver installation but requires a VISA installation on the controlling computer. VISA is
used to access the instrument, to send remote commands, and to read status informa-
tion.

Rohde

 

&

 

Schwarz provides the standardized I/O software library R&S

 

VISA for com-

munication via TCP/IP (LAN: HiSlip, VXI-11) or USB (USBTMC) interfaces. R&S

 

VISA

is available for download at the Rohde

 

&

 

Schwarz website 

www.rohde-schwarz.com/

rsvisa

.

USB Connection

www.allice.de

Allice Messtechnik GmbH

Содержание R&S RTM-B1























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды