background image

Preparing for use

R&S

®

HMP Series

17

Getting Started 1178.6791.02 ─ 03

Electromagnetic compatibility classes

The electromagnetic compatibility (EMC) class indicates where you can operate
the product. The EMC class of the product is given in the data sheet.

Class

 

B equipment is suitable for use in:

– Residential environments
– Environments that are directly connected to a low-voltage supply network

that supplies residential buildings

Class

 

A equipment is intended for use in industrial environments. It can cause

radio disturbances in residential environments due to possible conducted and
radiated disturbances. It is therefore not suitable for class B environments.
If class

 

A equipment causes radio disturbances, take appropriate measures to

eliminate them.

4.4

 

Setting up the R&S

 

HMP

See also:

"Setting up the product"

 

on page 7

"Intended use"

 

on page 5

4.4.1

 

Placing the R&S

 

HMP on a bench top

To place the product on a bench top

1. Place the product on a stable, flat and level surface. Ensure that the surface

can support the weight of the product. For information on the weight, see the
data sheet.

2.

CAUTION! 

Foldable feet can collapse. See 

"Setting up the product"

on page 7.
Always fold the feet completely in or out. With folded-out feet, do not place
anything on top or underneath the product.

3.

WARNING! 

A stack of products can fall over and cause injury. Never stack

more than three products on top of each other. Instead, mount them in a rack.
Stack as follows:
● If the products have foldable feet, fold them in completely.

Setting up the R&S

 

HMP

Содержание HMP Series


















































Отзывы: