Rohde & Schwarz HMF2525 Скачать руководство пользователя страница 6

Страница: 6 / 78

SCPI Commands HMF series

Remote Control

Basics

SCPI Programmers Manual

NOTICE

To establish a network connection, connect a commercial RJ-45 cable to one of the
LAN ports of the instrument and to a PC.

1.2.2 Configuring LAN Parameters

Depending on the network capacities, the TCP/IP address information for the instrument can be
obtained in different ways.

• If the network supports dynamic TCP/IP configuration using the Dynamic Host Configuration

Protocol (DHCP), and a DHCP server is available, all address information can be assigned
automatically.

•

Otherwise, the address must be set manually. Automatic Private IP Addressing (APIPA) is not
supported.

By default, the instrument is configured to use dynamic TCP/IP configuration and obtain all

address information automatically. This means that it is safe to establish a physical connection to

the LAN without any previous instrument configuration.

NOTICE

Risk of network errors

Connection errors can affect the entire network. If your network does not support

DHCP, or if you choose to disable dynamic TCP/IP configuration, you must assign valid

address information before connecting the instrument to the LAN. Contact your net-
work administrator to obtain a valid IP address.

Configuring LAN parameters

•

Press the MENU key and choose INTERFACE.

•

Press the knob, choose ETHERNET (SELECT INTERFACE) and PARAMETER.

• Define the IP and port settings of the instrument.
•

Select the IP Port - the port number for SCPI socket communication.

NOTICE

By default the instrument is not set to DHCP. If the instrument is set to DHCP and can-

not find a DHCP server, it takes about two minutes until the Ethernet menu is available.

Checking LAN and SCPI connection

•

Check the LAN connection using ping:

ping xxx.yyy.zzz.xxx

•

If the PC can access the instrument, enter the IP address into your PC internet browser:

http//:xxx.yyy.zzz.xxx

The „Instrument Home“ page appears. It provides information of the instrument and the LAN
connection.

Содержание HMF2525















































































Результаты поиска

Содержание HMF2525

Отзывы:

Rohde & Schwarz HMF2525, Руководство программиста, Страница: 6 / 78

Результаты поиска

Содержание HMF2525

Отзывы: