Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 55

Страница: 55 / 65

Command Reference

R&S

CMW-KM645

User Manual 1173.9740.02 ─ 04

<4_AudioLeftDev>

Audio left deviation,

Peak / 2

Range:

0 Hz to +96 kHz

Default unit: Hz

<5_AudioRightDev> Audio right deviation,

Peak / 2

Range:

0 Hz to +96 kHz

Default unit: Hz

<6_PilotFreqErr>

Pilot frequency error
Range:

-1500 Hz to +1500 Hz

Default unit: Hz

<7_RDSFreqDev>

RDS deviation
Range:

0 Hz to +96 kHz

Default unit: Hz

Example:

See

Performing Single Shot RF Measurements

Usage:

Query only

Firmware/Software:

V1.0.15.20 (RDS deviation added in V2.1.10)

FETCh:FMSTereo:MEAS<i>:MEValuation:RFModulation:SDEViation?
READ:FMSTereo:MEAS<i>:MEValuation:RFModulation:SDEViation?
CALCulate:FMSTereo:MEAS<i>:MEValuation:RFModulation:SDEViation?

Returns the standard deviation of the "RF Modulation" results.

The values described below are returned by

FETCh

and

READ

commands.

CALCulate

commands return limit check results instead, one value for each result listed below.

The number to the left of each result parameter is provided for easy identification of the
parameter position within the result array.

Return values:

<1_Reliability>

See

Reliability Indicator

<2_OutOfTol>

Out of tolerance result, i.e. percentage of measurement intervals
in the statistics cycle (

CONFigure:FMSTereo:MEAS<i>:

MEValuation:SCOunt:RFModulation

) exceeding the speci-

fied limits, see

Limit Settings

Range:

0 % to 100 %

Default unit: %

<3_PilotDev>

Standard deviation of the pilot deviation, RMS * SQRT2
Range:

0 Hz to +48 kHz

Default unit: Hz

<4_AudioLeftDev>

Standard deviation of the audio left deviation,

Peak / 2

Range:

0 Hz to +48 kHz

Default unit: Hz

Measurement Results

深圳德标仪器

135-1095-0799

Содержание CMW-KM645


































































Результаты поиска

Содержание CMW-KM645

Отзывы:

Бренды по названию

Популярные бренды

Rohde & Schwarz CMW-KM645, Руководство пользователя

Результаты поиска

Содержание CMW-KM645

Отзывы:

Бренды по названию

Популярные бренды