manualshive.com logo in svg

Rohde & Schwarz CMW-KM645, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 54

Command Reference

R&S

®

CMW-KM645

54

User Manual 1173.9740.02 ─ 04

<6_MultDevPos>

Standard deviation of the multiplex deviation, +Peak
Range: 

0 Hz to +96 kHz

Default unit: Hz

<7_MultDevNeg>

Standard deviation of the multiplex deviation, 

–

Peak

Range: 

0 Hz to +96 kHz

Default unit: Hz

<8_MultDevRMS>

Standard deviation of the multiplex deviation, RMS
Range: 

0 Hz to +48 kHz

Default unit: Hz

Example: 

See 

Performing Single Shot RF Measurements

Usage: 

Query only

Firmware/Software: 

V1.0.15.20

6.6.2 RF Modulation Results

The following commands return the statistical "RF Modulation" Results.

FETCh:FMSTereo:MEAS<i>:MEValuation:RFModulation:CURRent?
FETCh:FMSTereo:MEAS<i>:MEValuation:RFModulation:AVERage?
FETCh:FMSTereo:MEAS<i>:MEValuation:RFModulation:MAXimum?
READ:FMSTereo:MEAS<i>:MEValuation:RFModulation:CURRent?
READ:FMSTereo:MEAS<i>:MEValuation:RFModulation:AVERage?
READ:FMSTereo:MEAS<i>:MEValuation:RFModulation:MAXimum?
CALCulate:FMSTereo:MEAS<i>:MEValuation:RFModulation:CURRent?
CALCulate:FMSTereo:MEAS<i>:MEValuation:RFModulation:AVERage?
CALCulate:FMSTereo:MEAS<i>:MEValuation:RFModulation:MAXimum?

Returns the "RF Modulation" results.

The values described below are returned by 

FETCh

 and 

READ

 commands. 

CALCulate

commands return limit check results instead, one value for each result listed below.

The number to the left of each result parameter is provided for easy identification of the
parameter position within the result array.

Return values: 

<1_Reliability>

See 

Reliability Indicator

<2_OutOfTol>

Out of tolerance result, i.e. percentage of measurement intervals
in the statistics cycle (

CONFigure:FMSTereo:MEAS<i>:

MEValuation:SCOunt:RFModulation

) exceeding the speci-

fied limits, see 

Limit Settings

.

Range: 

0 %  to  100 %

Default unit: %

<3_PilotDev>

Pilot deviation, RMS * SQRT2
Range: 

0 Hz to +96 kHz

Default unit: Hz

 

Measurement Results

深圳德标仪器 

135-1095-0799

Содержание CMW-KM645


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды