manualshive.com logo in svg

Rohde & Schwarz CMW-KM645, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 53

Command Reference

R&S

®

CMW-KM645

53

User Manual 1173.9740.02 ─ 04

Return values: 

<Reliability>

See 

Reliability Indicator

<OutOfTol>

Out of tolerance result, i.e. percentage of measurement intervals
in the statistics cycle (

CONFigure:FMSTereo:MEAS<i>:

MEValuation:SCOunt:RFCarrier

 

on page 43) exceeding

the specified limits, see 

Limit Settings

.

Range: 

0 %  to  100 %

Default unit: %

<CarrierPower>

RF carrier power
Range: 

-130 dBm to +55 dBm

Example: 

See 

Performing Single Shot RF Measurements

Usage: 

Query only

Firmware/Software: 

V1.0.15.20

FETCh:FMSTereo:MEAS<i>:MEValuation:RFCarrier:SDEViation?
READ:FMSTereo:MEAS<i>:MEValuation:RFCarrier:SDEViation?
CALCulate:FMSTereo:MEAS<i>:MEValuation:RFCarrier:SDEViation?

Returns the standard deviation of the "RF Carrier" results.

The values described below are returned by 

FETCh

 and 

READ

 commands. 

CALCulate

commands return limit check results instead, one value for each result listed below.

The number to the left of each result parameter is provided for easy identification of the
parameter position within the result array.

Return values: 

<1_Reliability>

See 

Reliability Indicator

<2_OutOfTol>

Out of tolerance result, i.e. percentage of measurement intervals
in the statistics cycle (

CONFigure:FMSTereo:MEAS<i>:

MEValuation:SCOunt:RFCarrier

 

on page 43) exceeding

the specified limits, see 

Limit Settings

.

Range: 

0 %  to  100 %

Default unit: %

<3_CarrierPower>

Standard deviation of the carrier power
Range: 

0.0 dB  to  92.5 dB

Default unit: dB

<4_CarrierFreqErr>

Standard deviation of the carrier frequency error
Range: 

0 Hz to +96 kHz

Default unit: Hz

<5_MultDevPosNeg> Standard deviation of the multiplex deviation, 

±

Peak / 2

Range: 

0 Hz to +48 kHz

Default unit: Hz

Measurement Results

深圳德标仪器 

135-1095-0799

Содержание CMW-KM645


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды