manualshive.com logo in svg

Rohde & Schwarz CMW-KM645, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 41

Command Reference

R&S

®

CMW-KM645

41

User Manual 1173.9740.02 ─ 04

See also: "Measurement Control" in the R&S

 

CMW user manual, chapter "Remote

Control"

Return values: 

<MeasState>

OFF | RUN | RDY

OFF:

 measurement switched off, no resources allocated, no

results available (when entered after 

ABORt...

)

RUN:

 measurement running (after 

INITiate..., READ...

),

synchronization pending or adjusted, resources active or queued

RDY:

 measurement has been terminated, valid results may be

available
*RST: 

OFF

Example: 

See 

Continuous and AF Measurements

Usage: 

Query only

Firmware/Software: 

V1.0.15.20

Manual operation:

See 

"FM (Softkey)"

 

on page 19

FETCh:FMSTereo:MEAS<i>:MEValuation:STATe:ALL?

Queries the main measurement state and the measurement substates. Both measure-
ment substates are relevant for running measurements only. Use

FETCh:...:STATe?

 to query the main measurement state only. Use 

INITiate...,

STOP..., ABORt...

 to change the measurement state.

See also: "Measurement Control" in the R&S

 

CMW user manual, chapter "Remote

Control"

Return values: 

<MainState>

OFF | RDY | RUN

OFF:

 measurement switched off, no resources allocated, no

results available (when entered after 

STOP...

)

RDY:

 measurement has been terminated, valid results may be

available

RUN:

 measurement running (after 

INITiate..., READ...

),

synchronization pending or adjusted, resources active or queued
*RST: 

OFF

<SyncState>

PEND | ADJ | INV

PEND:

 waiting for resource allocation, adjustment, hardware

switching ("pending")

ADJ:

 all necessary adjustments finished, measurement running

("adjusted")

INV:

 not applicable because <main_state>: OFF or RDY ("inva-

lid")

Measurement Control and States

深圳德标仪器 

135-1095-0799

Содержание CMW-KM645


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды