Rohde & Schwarz 1402.9557.02 Скачать руководство пользователя страница 72

Страница: 72 / 80

Remote-control commands

DVB-H

Operating Manual 1008.0970.12 ─ 16

[:SOURce<hw>]:BB:DVB:DVBH|DVBT:IINTerleaver:SYMBol:MODE

<Mode>

The command selects the inner interleaver mode.

Parameters:

<Mode>

NATive | NATIve | IDEPth

NATive

The interleaver interleaves the bits over one OFDMA symbol.

IDEPth

The interleaver interleaves the bits over two (4K transmission
mode) or four (2K transmission mode) OFDMA symbols.
*RST:

NATive

Example:

BB:DVB:DVBH:IINT:SYMB:MODE NAT

sets the inner interleaver mode to "Native".

Manual operation:

See

"Inner Interleaver Mode"

on page 25

[:SOURce<hw>]:BB:DVB:DVBH|DVBT:IINTerleaver:SYMBol:TMODe

<TMode>

The command selects the transmission mode.

Parameters:

<TMode>

T2K | T4K | T8K
*RST:

T2K

Example:

BB:DVB:DVBH:IINT:SYMB:TMOD T2K

sets the transmission mode to T2K.

Manual operation:

See

"Inner Interleaver Tx Mode"

on page 25

[:SOURce<hw>]:BB:DVB:DVBH|DVBT:IINTerleaver:SYMBol[:STATe]

<State>

The command activates/deactivates the inner symbol interleaver.

Parameters:

<State>

0 | 1 | OFF | ON
*RST:

Example:

BB:DVB:DVBH:IINT:SYMB ON

activates the inner symbol interleaver.

Manual operation:

See

"Inner Symbol Interleaver"

on page 25

[:SOURce<hw>]:BB:DVB:DVBH|DVBT:OFDM:ALPHa

<Alpha>

The command selects the α value. This value is used to shape the constellation of the
modulation. For DVB-H, this value is always 1.

Parameters:

<Alpha>

1 | 2 | 4
*RST:

System Configuration

Содержание 1402.9557.02

















































































Результаты поиска

Содержание 1402.9557.02

Отзывы:

Бренды по названию

Популярные бренды

Rohde & Schwarz 1402.9557.02, Руководство по эксплуатации

Результаты поиска

Содержание 1402.9557.02

Отзывы:

Бренды по названию

Популярные бренды