For use with
4"
(outside diameter)
aluminum irrigation tubing.
(Not Supplied By Rocky's)
1
Insert one end of irrigation tubing into 4" hub
(item #65).
1
105
29
55
107
71
19
5
61
209
21
ROCKY'S EAZY ROLLERS INSTRUCTIONS - #3 PORTABLE
Bolt the castors (item #209) to the A-frames
(item #55), as shown in the diagram.
Assemble one end unit to the tube, using
the small handle (item #71), as shown in
the diagram.
Assemble the other end unit to the tube,
using the white knob (item #61).
For smoother operation, apply
petroleum based grease between the
hub (item #65) and the black bushing
(item #105). This should be done once a
year.
Position the assembled roller unit at the
widest end of the pool.
NOTE:
APPLY WATERPROOF
GREASE.
3
6
For regular shaped pools,
align the outside edge of the
tube parallel with the end of
the pool.
For irregular shaped pools,
the outside edge of the tube
should be 3'
i n s i d e
from the
end of
the pool.
5
1/16"
Insert the anchor bolt
(item #11) through
the spring (item
#25), through the
spring guard (item #109) and
through the hole of the A-frame.
Tools Required:
Reversible Electric Drill
1/2" Concrete (masonary) Drill Bit
Hammer & Center Punch or Nail.
5/16" Hex Head Socket Bit
1/2" Wrench
5/8" Wrench
SELF-DRILLING
NOTE:
Tube length should be about
1'
wider than pool.
65
2
MARK
#1
4
15
65
Slug
MARK
#2
This box contains the following items:
1
5
11
15
19
21
25
29
55
61
65
71
101
103
105
107
109
201
209
Self-tapping Screw
5/16"x1" Bolt
3/8"x6" Anchor Bolt
Concrete Anchor
5/16" Washer
3/8" Washer
Spring
Acorn Nut
#3 A-Frame
White Knob
4" Regular Hub
Small Handle
Male Grommet
Female Grommet
Plastic Bushing
Plastic Washer
Spring Guard
22' Strapping
2" Plastic Wheels
12
2
2
2
2
8
2
4
2
1
2
1
10
10
2
2
2
1
4
501
505
511
515
505
21
517
523
55
533
539
545
549
549
555
555
109
587
583
ITEM
#
DESCRIPTION
QTY.
RE-
ORDER
#
11
25
109
Any questions,check out our Web Site:
www.rockysrollers.com
Go to
FAQ
(Frequently AskedQuestiona)
®
V E R Y I M P O R TA N T
PREVENT DROWNING
Attach Warning Label to one end of tube.
Hit center slug
with hammer &
center punch,or
large nail.
Drive the concrete anchor into
the hole with a hammer.
Leave the anchor raised 1/
16".
To set the concrete anchor,
then tap the slug into the hole with a
hammer, then using a center punch or
large nail drive the slug down into the
anchor forcing legs out into concrete.
Using one of the two holes in the A-frame as a guide,
make mark #1 on deck. With a 1/2" concrete drill
bit, drill a 1 1/2" deep hole at mark #1. Complete
steps 5 and 6 before continuing with step 4.
On the other side of the roller unit, make mark #2 by
using one of the two holes in the A-frame as of guide.
With a 1/2" concrete drill bit, drill a 1 1/2" deep hole
at mark #2.
NOTE:
Set one bolt at front of frame on one end and
one at the rear of the frame on the other end.
Repeat with other side.
With 2 self-drill/tapping screws
(item #1), attach hub to tube using
electric drill. Apply pressure to
ensure screw cuts into
aluminum tube then cuts
it's own thread.
(No predrilling required)
