Rockwell ShopSeries RS8151, Инструкция по эксплуатации

Страница: 10 / 16

belt&disc sander en
10
before turning it on.
17. Avoid unintentional starting
Ensure switch is in “off” position when plugging in
18. Use outdoor extension leads
When the tool is used outdoors, use only extension
cords intended for outdoor use and so marked.
19. Stay alert
Watch what you are doing, use common sense and
do not operate the tool when you are tired.
20. Check damaged parts
Before further use of tool, it should be carefully
checked to determine that it will operate properly
and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service centre unless otherwise indicated in this
instruction manual.
Have defective switches replaced by an authorized
service centre.
Do not use the tool if the switch does not turn it on
and off.
21. Warning
The use of any accessory or attachment other than
one recommended in this instruction manual may
present a risk of personal injury.
22. Have your tool repaired by a qualified person
This electric tool complies with the relevant
safety rules. Repairs should only be carried out
by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.
23. If the replacement of the supply cord is necessary,
this has to be done by the manufacturer or his agent
in order to avoid a safety hazard.
24. For tools intended to be connected to a water
supply:
Replacement of the plug or the supply cord shall
always be carried out by the manufacturer of the
tool or his service organisation,
Keep water clear off the electrical parts of the tool
and away from persons in the working area.
additiOnal saFety rUles
1. Always wear eye protection.
2. Do not operate your machine until it is completely
assembled and installed according to the
instructions.
3. If you are not thoroughly familiar with the operation
of abrasive finishing machines, obtain advice
from your supervisor, instructor or other qualified
person.
4. Caution: This machine is designed to sand wood or
wood-like products only. Sanding or grinding other
materials could result in fire, injury or damage to
product.
5. This MACHINE is intended for indoor use only.
6. iMPOrtant: Mount and use this machine on
horizontal surfaces only. Operating machine when
mounted on non-horizontal surfaces might result in
motor damage.
7. If there is any tendency for the machine to tip over
or move during certain operations such as when
sanding long or heavy boards, the machine must be
securely fastened to a supporting surface.
8. Make sure the sanding belt is tracking correctly in
order that it does not run off the pulleys.
9. Make sure the sanding belt runs in the proper
direction. See directional arrow on back side of belt.
10. Make sure the sanding belt or disc is not torn or
loose.
11. Support workpiece firmly with the miter gage,
backstop or work table when sanding with the belt.
12. nOte: The only exception is curved work performed
on the top wheel of belt.
13. Always hold the workpiece firmly on the table when
sanding on the disc.
14. Avoid kickback by sanding in accordance with
directional arrows. Sand on downward side of
disc. Sanding on the upward side could cause the
workpiece to fly up causing injury.
15. Always maintain a minimum clearance of 1/16” or
less between the table or backstop and the sanding
belt or disc.
16. Never wear gloves or hold the work with a rag when
sanding.
17. Sand with the grain of the wood.
18. Do not sand pieces of material that are too small to
be safely supported.
19. Avoid awkward hand positions where a sudden slip
could cause a hand to move into the sanding belt or
disc.
20. When sanding a large workpiece, provide additional
support at table height.
21. Do not sand with the workpiece unsupported.
Support the workpiece with the backstop or table.
The only exception is curved work performed on the
outer sanding drum.
22. Always remove scrap pieces and other objects
from the table, backstop or belt before turning the
machine “ON.”