Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 428 | Manualshive

Страница: 428 / 548

background image

428

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 9

Troubleshoot the Switch

Collect System and
Configuration Information
for Technical Support

The Device Manager online Help provides a link that you can use to collect
system and configuration information about the switch. When you click the
link, the switch runs the

show tech-support

command via the command-line

interface (CLI). This command generates information about the switch that
can be useful to Technical Support when you report a problem.

To collect system and configuration information for Technical Support, follow
these steps.

1. Click the Help icon in the upper-right corner of the Device Manager

window.

2. In the Contents pane, click Support, and then click Information

commonly needed by field service.

The switch runs the

show-tech support

command and displays system

and configuration information in your browser window.

Help Icon

«
...
426
427
428
429
430
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Switch 4500 Family

Бренд: 3Com Страницы: 742

Бренд: 3Com Страницы: 940

Бренд: 3Com Страницы: 43

OfficeConnect WX1200

Бренд: 3Com Страницы: 646

Бренд: D-Link Страницы: 242

S5170-EI Series

Бренд: H3C Страницы: 46

PAT TRS 05 / PATB3

Бренд: Hirschmann Страницы: 12

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

SmartSwitch 2500

Бренд: Cabletron Systems Страницы: 402

Бренд: Electroswitch Страницы: 6

Бренд: I-Tech Страницы: 29

Бренд: Good Way Страницы: 13

Бренд: INDO Страницы: 3

Бренд: Taiden Страницы: 4

Бренд: Ruby Tech Страницы: 2

Бренд: Smartwares Страницы: 44

Бренд: H3C Страницы: 19

Бренд: SEKURYX Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды