Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 362 | Manualshive

Страница: 362 / 548

background image

362

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 7

Configure Switch Features

Spanning Tree Protocol (STP) modes include the following:

• Multiple Spanning Tree (MST) prevents network loops by enabling

only one active path for traffic. MST also provides a redundant path if
the active path becomes unavailable. This is the default STP mode. If
you connect the switch to a Cisco network switch, the typical default is
PVST+, not MST. To provide compatibility, one or the other switch
must be modified.

• Per VLAN Spanning Tree Plus (PVST+) runs on each VLAN on the

switch up to the maximum supported to prevent network loops.

• Rapid Per VLAN Spanning Tree Plus (RPVST+) immediately deletes

dynamically learned MAC address entries upon receiving a topology
change. By contrast, PVST+ uses a short aging time for dynamically
learned MAC addresses.

We recommend that you leave STP enabled to prevent network loops and
provide a redundant path if the active path becomes unavailable.

Configure STP via Device Manager

From the Configure menu, choose STP Settings.

Global Settings

To choose the STP mode for the switch or to configure STP on individual
VLANs, click the Global tab. On the Global tab, you can add, edit, or delete
instances. If you choose PVST+ or Rapid PVST+ mode, you can enable or
disable STP on each instance.

IMPORTANT

Disabling STP can affect connectivity to the network.

«
...
360
361
362
363
364
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

DGS-1024D - Switch

Бренд: D-Link Страницы: 16

DGS-1016D - Switch

Бренд: D-Link Страницы: 44

DES-6000 Series

Бренд: D-Link Страницы: 3

DES-5024 - Switch

Бренд: D-Link Страницы: 2

DES-3828 - xStack Switch - Stackable

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 192

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 110

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 4

DGS-105 - Switch

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

Бренд: OFFICINE OROBICHE Страницы: 7

DES-3224 - Switch

Бренд: D-Link Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды