Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 548

background image

204

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

Chapter 7

Configure Switch Features

Configure Time Synchronization via the Logix Designer Application

To configure time synchronization, follow these steps.

1. In the navigation pane, click Time Sync Configuration.

2. From the Clock Type pull-down menu, choose a mode.

The available modes vary based on the switch model.

3. To complete the remaining fields, refer to the figure and table that

corresponds to your mode.

Sync Interval

Type the time interval, specified as the logarithmic mean in seconds, for sending synchronization messages.
Valid values:

• -1—half second
• 0—1 second
• 1— 2 seconds
Default: 0 (1 second)

Sync Fault Limit

Type the maximum clock offset before PTP attempts to reacquire synchronization.
Valid values: 50…500000000 nanoseconds

Default: 50000 nanoseconds

IMPORTANT:

We recommend against setting the sync limit below the default (50000 nanoseconds). Use values below 50000 nanoseconds only in

networks with a very high-precision grandmaster clock. These networks have a critical need to keep very sensitive devices synchronized.

Vlan Id

To configure PTP on a VLAN of a trunk port, type the VLAN ID. Only PTP packets in the VLAN you specify are processed. PTP packets from other
VLANs are dropped. You can only enable PTP on one VLAN on a trunk port.
Valid values: 1…4094
The default is the native VLAN of the trunk port.

Table 36 - NTP-PTP Clock Mode Fields (Continued)

Field

Description

Mode

Page

Boundary

End to End

Forward

NTP-PTP Clock

«
...
202
203
204
205
206
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

SmartPro DGS-1500-20

Бренд: D-Link Страницы: 113

xStack DGS-3120 Series

Бренд: D-Link Страницы: 1150

Бренд: Kathrein Страницы: 8

Бренд: Nayar Systems Страницы: 21

Бренд: Kathrein Страницы: 24

Бренд: Kasia Страницы: 5

Бренд: Gavita Страницы: 12

DMS-1250 Series

Бренд: D-Link Страницы: 38

Бренд: Sangamo Страницы: 2

OSD2700F SERIES

Бренд: Optical Systems Страницы: 29

Бренд: Metra Electronics Страницы: 8

Бренд: Popp Страницы: 9

Бренд: Generac Power Systems Страницы: 2

OSD2251P Series

Бренд: Optical Systems Design Страницы: 48

Бренд: Ortech Страницы: 3

Бренд: Madas Страницы: 24

Chief Kontour KPWR Series

Бренд: LEGRAND Страницы: 8

Бренд: QNAP Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды