Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 548

background image

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

131

Install Stratix 5700 Switches

Chapter 5

• Temperature surrounding the unit does not exceed 60 °C (140 °F).

• Clearance to front and rear panels meets these conditions:

– Front-panel status indicators can be easily read.
– Access to ports is sufficient for unrestricted cabling.
– Front-panel direct current (DC) power connectors and the alarm

relay connector are within reach of the connection to the DC power
source.

• Cabling is away from sources of electrical noise, such as radios, power

lines, and fluorescent lighting fixtures.

• Connect the unit to only a Class 2 DC power source.

Follow these steps to install the switch.

1. (Optional) Install or remove the SD card.

2. Verify switch operation.

3. Mount the switch on a DIN rail.

4. Ground the switch.

5. Wire the DC power source for the switch and attach the switch power

connectors.

6. (Optional) Wire the Power over Ethernet (PoE) DC power source and

attach the PoE power connector.

7. (Optional) Install an SFP module.

8. Wire external alarms and attach the alarm relay connector to the switch.

9. Connect to the switch ports:

• 10/100 copper ports and 10/100/1000 ports
• 10BASE-T, 100BASE-TX, and 10000BASE-T ports
• PoE ports
• SFP module ports
• Dual-purpose ports

IMPORTANT

When the switch is installed in an industrial enclosure, the

temperature within the enclosure is greater than normal room
temperature outside the enclosure.

The temperature inside the enclosure cannot exceed 140 °F (60 °C),

the maximum ambient enclosure temperature of the switch.

ATTENTION:

Do not wire more than 1 conductor on any single terminal.

«
...
129
130
131
132
133
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

Бренд: D-Link Страницы: 73

Бренд: RDL Страницы: 4

Бренд: UfiSpace Страницы: 25

Бренд: Equip Страницы: 10

LVP-51 LVP-51 Series

Бренд: Omega Engineering Страницы: 6

Digital Energy STS-400-25-3

Бренд: GE Страницы: 49

IPES-5222T Series

Бренд: Lantech Страницы: 30

Бренд: Canoga Perkins Страницы: 7

Бренд: GarrettCom Страницы: 77

SmartStack STS16-20R

Бренд: Cabletron Systems Страницы: 258

Бренд: Larson Electronics Страницы: 2

ControlZAPP CZ CESR 10VDC

Бренд: DANLERS Страницы: 2

Бренд: Gigacore Страницы: 8

ProSAFE FS526Tv2

Бренд: NETGEAR Страницы: 20

Бренд: Scion-Tech Страницы: 9

Бренд: N-Tron Страницы: 15

Бренд: CoolGear Страницы: 8

Бренд: Southern States Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды