Rockwell Automation Guardmaster 440R-ENETR, Руководство пользователя, Страница: 58 / 86

58 Rockwell Automation Publication 440R-UM009C-EN-P - July 2019
Chapter 6 AOP Controller Tags
GLT Fault Codes
CrossLoopFault BOOL Cross Loop Fault – Indicates that a short circuit is present from terminal S11 to terminal S21, or short circuit from S11 to 24V or from
S21 to 24V.
• Case 1: The input circuit is open (gate is open)
The PWR/Fault indicator is solid green.
Close the gate and press the reset button to clear the fault.
• Case 2: The input circuit is closed (gate is locked)
The PWR/Fault indicator is green with red flashing 5X.
Remove the fault and cycle power to the GLP to clear the fault.
• Case 3: The input circuit is open (E-stop pushed).
The PWR/Fault indicator is solid green.
Remove the fault and release the E-stop to clear the fault.
• Case 4. The input circuit is closed (E-stop released)
The PWR/Fault indicator is solid green.
Remove the fault and cycle the E-stop to clear the fault.
0 = No fault
1 = Fault
S12OpenWire BOOL S12 Open Wire Fault – Indicates that the circuit to terminal S12 opened when it was expected to be closed. The PWR/Fault indicator is
green with red flashing 5X. Check the wiring at S12 and its source. Open and close the gate to clear the fault.
If the Logic setting is 5…8, then a short circuit from S12 to 0V also sets this bit to 1. The PWR/Fault indicator is solid green. Remove
the short circuit and cycle the E-stop button to clear the fault.
0 = No fault
1 = Fault
S22OpenWire BOOL S22 Open Wire Fault – Indicates that the circuit to terminal S22 opened when it was expected to be closed. The PWR/Fault indicator is
green with red flashing 5X. Check the wiring at S22 and its source. Open and close the gate to clear the fault.
If the Logic setting is 5…8, then and a short circuit from S22 to 0V sets this bit. Remove the short circuit and cycle the E-stop to clear
the fault.
0 = No fault
1 = Fault
LockRequest_GateOpen BOOL Lock Request/Reset Gate Open Fault - Indicates that the gate was open during a lock or reset request. The PWR/Fault indicator is green
with red flashing 3X. Close the gate and press the unlock button to clear the fault.
0 = No fault
1 = Fault
Gate_Retrigger_Fault BOOL Gate Retrigger Fault – With the GLP configured for non-retriggerable delay, the E-stop was released before the time delay expired.
The PWR/Fault indicator is green with red flashing 4X. After the timing cycle expires, cycle the E-stop button to clear the fault.
0 = No fault
1 = Fault
GateOpen_Fault BOOL Gate Open Fault - Indicates the gate inputs, S12 and S22, unexpectedly opened, or a cross loop fault occurred when the gate was
locked. The PWR/Fault indicator is green with red flashing 5X. Close the gate and press the reset button to clear the fault.
0 = No Fault
1 = Fault
Table 15 - GLT Relay Tags (Tag name prefix: ENETRname:I.Relayx_GSR_GLT.)
Name Data Type Definition
Table 16 - GLT Relay Nonrecoverable Fault Codes
Fault Code
Decimal (Hex) Description Recommended Action
00 (00) No Fault No action needed.
05 (05) S11 Pulse Test
Follow the general instructions for faults. See General Instructions for Faults on page 39 .
06 (06) S21 Pulse Test
07 (07) OSSD1 Check for short circuits at terminal 14 to 24V and 0V.
Processor A shows 07. Processor B shows 07 (24V short).
Processor A shows 07. Processor B shows 02 (0V short).