background image

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019

7

Shaft Seal Kits for Kinetix TLP Servo Motors

Additional Resources

These documents contain additional information concerning related products from Rockwell 
Automation.

You can view or download publications at 

http://www.rockwellautomation.com/global/

literature-library/overview.page

.

Resource

Description

Kinetix Rotary Motion Specifications Technical Data, 
publication 

KNX-TD001

 

Product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPH, 
VPS), MP-Series™ (Bulletin MPL, MPM, MPF, MPS), and TL-Series™ 
rotary motors.

Kinetix Motion Accessories Specifications Technical Data, 
publication 

KNX-TD004

 

Product specifications for Bulletin 2090 motor and interface cables, 
low-profile connector kits, drive power components, and other servo 
drive accessory items.

Kinetix Motion Control Selection Guide,
publication 

KNX-SG001

 

Overview of Kinetix servo drives, motors, actuators, and motion 
accessories that are designed to help make initial decisions for the 
motion control products best suited for your system requirements. 

Industrial Automation Wiring and Grounding Guidelines, 
publication 

1770-4.1

 

Provides general guidelines for installing a Rockwell Automation 
industrial system.

Product Certifications website, 

rok.auto/certifications

Provides declarations of conformity, certificates, and other 
certification details.

Содержание Allen-Bradley TLP-SSN-F046









Отзывы: