background image

2

Rockwell Automation Publication 2090-IN044B-EN-P - September 2019

Shaft Seal Kits for Kinetix TLP Servo Motors

About Shaft Seals

A shaft seal is recommended if the motor shaft and end bell are exposed to significant amounts of 
containments, such as oil, fluids, or fine dust. Use a shaft seal in these environments to prolong 
the life of the motor. A shaft seal and Bulletin 2090 cables with environmentally sealed 
connectors are required for an IP65 rating or greater.

See Kinetix® Motion Accessories Specifications Technical Data, publication 

KNX-TD004

, to 

find Bulletin 2090 cables with environmentally sealed connectors for your motor.

Required Tools

Use these tools to install a shaft seal:

• Insulated, small, flat-head screw driver

• Rubber/wooden mallet or a metal hammer and wooden work piece

• Socket, pipe, or tube (various sizes)

• Abrasive cloth to remove any nicks or burrs from the motor shaft

Required Supplies

Lubricant - Grease, industrial grade, suitable for applications with speeds up to 6000 RPM, and 
–10…+80 °C (14…176 °F) temperature range.

IMPORTANT

The shaft seal is not required in applications where the motor shaft and end bell are free of oil, 
fluids, or fine dust, and a lower IP rating is sufficient.

Shaft seals are subject to wear and require periodic inspection and replacement. Replacement 
is recommended every 3 months, not to exceed 12 months, depending on use.

If you paint the motor, do not get paint on the shaft seal area or the shaft, as paint can decrease 
the life of the shaft seal.

Oil, Fluids, and Fine Dust

Oil, Fluids, and Fine Dust

Shaft Seal Installations 
Recommended

Shaft Seal Installation
is Not Recommended

Motor Shaft and 
End Bell are Exposed 
to Containments

Motor Shaft and 
End Bell are Protected 
From Containments

Shaft Seal Installation
is Not Recommended

Содержание Allen-Bradley TLP-SSN-F046









Отзывы: