manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex SCR, Руководство пользователя

Поделиться
Скачать
Rockwell Automation Allen-Bradley PowerFlex SCR Скачать руководство пользователя страница 19

Installation/Wiring

1-5

PowerFlex SCR Bus Supply User Manual

Publication 20S-UM001G-EN-P

 

 

 

General Grounding 

Requirements

The Safety Ground terminal

 

(PE) must be connected to the building 

grounding scheme. Ground impedance must conform to the requirements 
of national and local industrial safety regulations and/or electrical codes. 
The integrity of all ground connections should be periodically checked.

For installations within a cabinet, a single safety ground point or ground bus 
bar connected directly to building steel should be used. All circuits 
including the AC input ground conductor should be grounded 
independently and directly to this point/bar.

Figure 1.3 Typical Grounding  

Safety Ground Terminal - PE

The Bus Supply safety ground (PE) must be connected to the customer 
grounding scheme or earth ground. This is the safety ground for the Bus 
Supply that is required by code. This point must be connected to adjacent 
building steel (girder, joist), a floor ground rod, bus bar or building ground 
grid. Grounding points must comply with national and local industrial 
safety regulations and/or electrical codes.

RFI Filter Grounding

Using an external RFI filter may result in relatively high ground leakage 
currents. Therefore, the filter must only be used in installations with 
grounded AC supply systems and be permanently installed and solidly 
grounded (bonded) to the building power distribution ground. Ensure that 
the incoming supply neutral is solidly connected (bonded) to the same 
building power distribution ground. Grounding must not rely on flexible 
cables and should not include any form of plug or socket that would permit 
inadvertent disconnection. Some local codes may require redundant ground 
connections. The integrity of all connections should be periodically 
checked. Refer to the instructions supplied with the filter.

+DC

SCR

Bus Supply

- DC

R (L1)
S (L2)
T (L3)

PE

Ground Grid, Girder or Ground 

Rod (Building Ground Potential)

Содержание Allen-Bradley PowerFlex SCR





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды