Rockwell Automation Allen-Bradley PowerFlex 755T Series Скачать руководство пользователя страница 115

Страница: 115 / 130

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

115

Chapter 4 Troubleshooting

Configurable LCL Filter

Capacitor Failure Response

Review the Attention statement that follows if you intend to configure the Line
Side Converter to produce an alarm instead of a fault when the LCL Capacitor
Failure event occurs.

Configurable LCL Filter

Capacitor Over Resonance

Response

Review the Attention statement that follows if you intend to configure the line
side converter to produce an alarm instead of a fault when the LCL Capacitor
Over Resonance event occurs.

ATTENTION:

You must read the following information before you can enable

the Line Side Converter to produce an alarm instead of a fault when the

LCL Filter Capacitor Failure

event occurs.

Operating the product (drive or bus supply) during the LCL Capacitor Failure

event may damage the LCL filter. This damage may lead to catastrophic

product failure and collateral damages.
It is your responsibility to configure drive parameters, understand the

causes and consequences of LCL capacitor failure, and meet safety

requirements in accordance with all applicable codes and standards. If

enabling the Line Side Converter to produce an alarm instead of a fault

when the LCL Capacitor Failure event occurs is desired, you must certify the

safety of the application. To acknowledge that you have read this ‘Attention’

and properly certified the application, set bit 6 ‘CapFailAlrm’ of parameter

13:40 [Conv Options Cfg]. This action removes Fault 24, ‘CapFailureCfg’. It

allows parameter 0:452 [LCLCapFailActn] to be set to 0 ‘Alarm’, enabling an

alarm instead of a fault.

ATTENTION:

You must read the following information before you can enable

the Line Side Converter to produce an alarm instead of a fault when the

LCL Filter Capacitor Over Resonance

event occurs.

Operating the product (drive or bus supply) during the LCL Capacitor Over

Resonance event may damage the LCL filter. This damage may lead to

catastrophic product failure and collateral damages.
It is your responsibility to configure drive parameters, understand the

causes and consequences of LCL capacitor over resonance, and meet

safety requirements in accordance with all applicable codes and standards.

If enabling the Line Side Converter to produce an alarm instead of a fault

when the LCL Capacitor Over Resonance event occurs is desired, you must

certify the safety of the application. To acknowledge that you have read this

‘Attention’ and properly certified the application, set bit 5 ‘CapORsncAlrm’ of

parameter 13:40 [Conv Options Cfg]. This action removes Fault 56,

‘CapOvrRsncCfg’. It allows parameter 0:453 [CapOvrRsncActn] to be set to 0

‘Alarm’, enabling an alarm instead of a fault.

Содержание Allen-Bradley PowerFlex 755T Series



































































































































Результаты поиска

Содержание Allen-Bradley PowerFlex 755T Series

Отзывы:

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Руководство по программированию, Страница: 115 / 130

Результаты поиска

Содержание Allen-Bradley PowerFlex 755T Series

Отзывы: