background image

Rockwell Automation Publication 1734-IN032F-EN-P - September 2022

9

POINT I/O 4 Channel High Density Current Input Module Installation Instructions

Remove a 1734-TOPS Base

1.

To remove a wiring base from the DIN rail, you must remove the module that is installed to the right of the base.

2.

Squeeze the module locking mechanism of the module to the right of the base, pulling up to remove the module. 

3.

Turn the orange locking screw to a vertical position to unlock the base from the DIN rail. 

4.

Slide the base up to release it from its mating units. 

Wire the Module

Wiring Diagram

 

WARNING: 

If you connect or disconnect wiring while the field-side power is on, an electric arc can occur. This could cause an explosion in hazardous 

location installations. Be sure that power is removed or the area is nonhazardous before proceeding.

Channel

Current Input

Common

Chassis Ground

0

0

4 or 5

6 or 7

1

1

2

2

3

3

12/24V DC is provided by the internal power bus.

1734

IE4C

Input 0 connection

C

Input 1 connection

C

Chas Gnd = Chassis ground
C = Common

Chas Gnd

Chas Gnd

Input 2 connection

Input 3 connection

In = Input channel
Chas Gnd = Chassis Ground
C = Common

4-wire

AC or DC

In 0

In 1

C

C

Chas 
Gnd

3

5

7

0

1

2

4

6

In 2

In 3

Chas 
Gnd

Current 
input 
device

Current 
input 
device

2-wire

(1) 1734-VTM is optional. Use the 24V DC supply from 1734-VTM module for 2-wire/3-wire devices.

V

V

V

V

V

3

5

7

0

1

2

4

6

V

V

V

1734-IE4C

1734-VTM

(1)

V (Voltage Out) = 24V DC

Содержание Allen-Bradley POINT I/O 1734-IE4C

















Отзывы: