Rockwell Automation Allen-Bradley MP-Series Скачать руководство пользователя

Страница: 46 / 68

MP-Series Heavy Duty Electric Cylinders

Rockwell Automation Publication MPAI-IN001E-EN-P - March 2012

Lubrication

Your electric cylinder has been lubricated at the factory and is ready for installation. Use the

appropriate lubrication interval calculations listed below for schedule estimates or use Rockwell

Motion Analyzer software to calculate the recommenced re-grease schedule for the electric

cylinder. Lubrication kits are shown on

page 59.

The type of lubricant and the appropriate maintenance interval is dependent on the type of

electric cylinder and one or more usage factors:

•

Ball screw catalog number MPAI-

xxx

C does not require lubrication.

•

Ball screw (catalog number MPAI-

xxxxx

C or MPAI-

xxxxx

E) electric cylinders use

Mobilith SHC220 lubricant. A maximum case temperature above or below 50 °C

(125 °F) during operation determines the lubrication interval.

•

Roller screw (catalog number MPAI-

xxxxx

R or MPAI-

xxxxx

S) electric cylinders require

lubrication at an interval that must be calculated. Factors in the calculation include

severity of use, screw lead pitch, and frame size.

Ball Screw Lubrication

Lubrication is recommended at these intervals:

•

Light to moderate - The case temperature does not exceed 50 °C (125 °F), and does not
require additional lubrication.

•

Severe duty - The case temperature exceeds 50 °C (125 °F), and requires refilling of the
lubricant reservoir through the grease fitting at 1000 hours of use.

Use Mobilith SHC220 to lubricate the ball screw. Set your browser to

http://www.mobil.com

view the Mobilith SHC220 product information.

ATTENTION:

Overfilling of the lubricant reservoir reduces performance, and may lead to heat

build-up and premature failure of the electric cylinder.

TIP

A grease gun typically delivers one gram of lubricant for one pump of the gun.

IMPORTANT

The maximum lubricant fill capacity for ball screw drives is the following:

•

3.0 g of Mobilith SHC220 for frame size 83

•

5.0 g of Mobilith SHC220 for frame size 110

•

6.0 g of Mobilith SHC220 for frame size 144

Содержание Allen-Bradley MP-Series





































































Результаты поиска

Содержание Allen-Bradley MP-Series

Отзывы:

Похожие инструкции для Allen-Bradley MP-Series

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley MP-Series, Руководство по установке

Результаты поиска

Содержание Allen-Bradley MP-Series

Отзывы:

Похожие инструкции для Allen-Bradley MP-Series

Бренды по названию

Популярные бренды