Rockwell Automation Allen-Bradley 856T-B24LC Скачать руководство пользователя страница 35

Страница: 35 / 82

Rockwell Automation Publication 856T-UM001B-EN-P - April 2021

Chapter 4 IO-Link Parameters

Common Tab

The Common tab contains the following device information:

Table 3 - Common Tab

Parameter

Description

Vendor

Provides the vendor name that is assigned to Vendor ID.

Vendor Text

Field used to describe additional product information. In this case, it displays product

Internet webpage address.

Vendor ID

Describes the worldwide unique vendor ID of the manufacturer of the product as

designated in the IO-Link Consortium.

URL

Displays the vendor URL.

Device

Provides the specific catalog number of the product.

Description

This parameter displays the product description.

Device ID

Displays the unique device ID as defined in the IO-Link specifications.

IO-Link Revision

Displays the current IO-Link version that the device supports.

Hardware Revision

Displays the device hardware revision number.

Firmware Revision

Displays the device firmware revision number.

Bitrate

Displays the supported bitrate for communications as defined in the IO-link 1.1 standard.

Minimum Cycle Time The parameter to inform the master about the shortest cycle time supported by the

device. Value is given in microseconds.

IODD

Information about the IODD that has been used to configure the 856T-B24LC module.

SIO mode

Information whether the device supports the SIO (Standard Input and Output).

Document Version

Displays information about the IODD version that has been used to configure the IO-Link

device

Date of Creation

This field displays date when the IODD file has been CRC stamped

Содержание Allen-Bradley 856T-B24LC



















































































Результаты поиска

Содержание Allen-Bradley 856T-B24LC

Отзывы:

Rockwell Automation Allen-Bradley 856T-B24LC, Руководство пользователя, Страница: 35 / 82

Результаты поиска

Содержание Allen-Bradley 856T-B24LC

Отзывы: