manualshive.com logo in svg

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Поделиться
Скачать
Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 70

70

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Appendix D

Mechanical Interlock for 7712 and PowerFlex 7000 Drive

Transfer Block

• Standard Transfer Block located inside drive cabinet.
• All 5 KC Keys need to be placed in the transfer block to release KA and 

KB

Connections

Motor Connection from 7791

Limited to one cable per phase.

Motor Connection from 7712

Limited to one cable per phase.

Interlock Operation 

Sequence (One Motor)

Initial Condition

• All doors closed
• Bypass, Drive Input, Drive Output contactors in open and the cart 

withdrawn.

• Bypass earth switch closed
• KC and KD keys in earth switch
• KA key in the Drive Input cabinet (in transfer block)
• KB key in Drive Output cabinet (in transfer block)
• KC keys (4) in transfer block, one in earth switch in Bypass cabinet

To Run Drive

• Open earth switch, lock open with KC
• Place all KC keys in transfer block
• Take KA and KB keys and place in Drive Input and Drive Output doors
• Turn keys to unlock carts
• Rack-in Drive Input and Drive Output carts.
• Run drive

Содержание Allen-Bradley 7712











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды