manualshive.com logo in svg

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Поделиться
Скачать
Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 37

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

37

Chapter

 5

Maintenance

Required Tools

• Torque wrench: 0…48 lb•ft (0…65 N•m)
• Sockets: 3/8 in., 7/16 in., 9/16 in.
• Ratchet handle and extension
• Wrenches: 7/16 in., 1/2 in., 9/16 in.
• Feeler gauges: 0.050 in. (1.3 mm), 0.080 in. (2 mm), 0.020 in. (0.5 mm)
• Flat-blade screwdriver
• Nyogel 759G Lubricant (Allen-Bradley part no. 80158-357-51)
• MV Door Key
• Allen Key
• Speed Wrench
• Cart-latch key
• Earthing Switch operating tool

Maintenance of Industrial 

Control Equipment

Periodic Inspection 

Industrial control equipment should be inspected periodically. Inspection 

intervals should be based on environmental and operating conditions and 

adjusted as indicated by experience. An initial inspection within 3...4 months 

after installation is suggested. See National Electrical Manufacturers 

Association NEMA) Standard No. ICS 1.3, Preventive Maintenance of 

Industrial Control and Systems Equipment, for general guidelines for setting-

up a periodic maintenance program. Some specific guidelines for Rockwell 

Automation products are listed below.

ATTENTION: 

Servicing energized Industrial Control Equipment can be 

hazardous. Severe injury or death can result from electrical shock, bump, or 
unintended actuation of controlled equipment. Recommended practice is to 
disconnect and lockout control equipment from power sources, and release 

stored energy, if present. Refer to National Fire Protection Association 
Standard No. NFPA70E, Part II and (as applicable) OSHA rules for Control of 
Hazardous Energy Sources (Lockout/Tagout) and OSHA Electrical Safety 

Related Work Practices for safety related work practices, including procedural 
requirements for lockout-tagout, and appropriate work practices, personnel 
qualifications and training requirements where it is not feasible to de-

energize and lockout or tagout electric circuits and equipment before 
working on or near exposed circuit parts.

Содержание Allen-Bradley 7712











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды