Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 15

Страница: 15 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Chapter

Safety Interlock and Accessibility

Requirements

Recommended Torque

Values

When installing line and load cables or enclosure access panels, use the

following torque specifications.

Table 2 - Hardware Torque Specifications

ATTENTION:

This procedure requires contact with medium voltage

components. To avoid shock hazards, complete the Power Lockout procedure
on

page 27

before servicing the equipment. Verify with a hot stick or

appropriate voltage measuring device that all circuits are voltage free. Failure
to do so may result in severe burns, injury or death.

IMPORTANT

For general information on handling medium voltage controllers and

preparing the installation site, see publication

MV-QS050

ATTENTION:

Use suitable personal protective equipment (PPE) per local

codes or regulations. Failure to do so may result in severe burns, injury, or

death.

Hardware Size

Tightening Torque Required

1/4 in. (M6)

6 ft•lb (8 N•m)

5/16 in. (M8)

12 ft•lb (16 N•m)

3/8 in. (M10)

20 ft•lb (22 N•m)

1/2 in. (M14)

48 ft•lb (65 N•m)

ATTENTION:

Some components of this product incorporate Imperial

hardware. Rockwell Automation recommends the use of the appropriate
tools to successfully complete the maintenance procedures on these

components. If you cannot obtain such tools, contact your area Rockwell
Automation sales office for assistance.

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды